journal article·1985-03

Strengthening mechanisms in high-strength microalloyed steels

D. T. Gawne, G. M. H. Lewis

Publisher page

Abstract

The mechanisms responsible for strengthening a series of high-strength cold-rolled steels with tensile strengths up to 800 MN m−2 have been investigated. The magnitude of precipitation strengthening in the annealed steels is shown to be in agreement with the Orowan-Ashby model for non-deforming particles. Strengthening depends only upon the volume fraction and diameter of the precipitates, and is not influenced by their chemical composition, nor by whether the precipitation-hardening elements are added singly or in combination. Manganese alone is a weak solid-solution-strengthening agent, but has a synergistic effect in combination with titanium or niobium, which is attributed to its depression of the austenite-ferrite transformation and precipitation temperatures. Vanadium is a much less efficient strengthening element than titanium or niobium in annealed steel, owing to the rapid coarsening rate of vanadium carbonitride precipitates and the considerable loss in strength on processing from hot-rolled coil to annealed sheet. Sulphur acts to reduce the strength of the annealed steels and tends to coarsen the grain structure. The physical basis of this effect is not known, but it is suggested that it may be associated with the partial solution of managanese sulphide during slab reheating and its subsequent re-precipitation during hot rolling. Phosphorus and nitrogen are the most efficient strengthening agents up to tensile strengths of 450 MN m−2, but stronger materials require a combination of strengthening modes, depending upon the application.MST/111
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. BEARDMORE P. · Mater. Eng., · 1981 · 2 · 250
2. HABERFIELD A. B. · Metall. Mater. Technol., · 1982 · 14 · 405
3. EVANS R. W. · J. Iron Steel Inst., · 1967 · 205 · 1150
4. 10.1007/BF0281787910.1007/BF02817879 ↗
5. 10.1179/03071697980327624610.1179/030716979803276246 ↗
6. IvriasuotcA T. · Metall. Trans., · 1975 · 6 · 161310.1007/BF02641975 ↗
7. 10.1179/msc.1967.1.1.4010.1179/msc.1967.1.1.40 ↗
8. LI J. C. M. · Trans. AIME · 1963 · 227 · 239
9. D. T. GAWNE and G. T. HIGGINS: in ‘Textures in research and practice’, 319; 1969, Berlin, Springer-Verlag.10.1007/978-3-662-13125-1_23 ↗
10. MOULD P. R. · Met. Eng. Q., · 1975 · 15 · 22
11. 10.1179/mst.1985.1.2.12810.1179/mst.1985.1.2.128 ↗
12. ARAKI K. · Trans. Iron Steel Inst. Jpn · 1977 · 17 · 70110.2355/isijinternational1966.17.701 ↗
13. L. MEYER, F. HEISTERKAMP, and D. LAUTERBORN: ‘Processing and properties of low carbon steel’, 297; 1973, New York, Metallurgical Society of AIME.
14. MEYER L. · Z. Metallkd., · 1967 · 58 · 334
15. MEYER L. · Dissertation · 1966
16. MEYER L. · Z. Metallkd., · 1967 · 58 · 396
17. MANDRY P. · Compt. Rend., · 1966 · 263 · 1118
18. HUDD R. C. · J. Iron Steel Inst., · 1971 · 209 · 121
19. M. F. ASHBY: in ‘Oxide dispersion strengthening’, 143; 1958, New York, Metallurgical Society of AIME.
20. T. GLADMAN, B. HOLMES, and I. D. McIVOR: in ‘Effect of second-phase particles on the mechanical properties of steel’, 68; 1971, London, The Iron and Steel Institute.
21. K. J. IRVINE: in ‘Heat treatment of metals’, 37; 1966, London, The Iron and Steel Institute.
22. 10.1016/0036-9748(70)90082-710.1016/0036-9748(70)90082-7 ↗
23. 10.1179/03063458079042645410.1179/030634580790426454 ↗
24. 10.1179/03071698180327552310.1179/030716981803275523 ↗