journal article·2004-11

Relative importance of transformation temperatures and sulphur content on hot ductility of steels

A. Cowley, B. Mintz

Materials Science and Technology· Volume 20· Issue 11
Publisher page

Abstract

Low (0·3%) and high manganese (1·4%) plain C – Mn steels with varying sulphur levels have had their hot ductility determined over the temperature range 700 – 1000°C, both after ‘solution treatment’ at 1330°C and directly after casting. It has been established that the width, depth and position of the hot ductility curves after solution treatment is more related to the transformation behaviour than either the sulphur in solution or the sulphide volume fraction or distribution. The growth of deformation induced ferrite at the austenite boundaries seems to be mainly diffusion controlled, and the higher is the transformation temperature for the γ – α phase change, the faster is the growth. Large amounts of ferrite can then form, giving good ductility. Thus, high transformation temperatures Ae 3 or Ar 3 are required to produce narrow ductility troughs. It is believed that any detrimental influence of the sulphides on these ‘solution treated’ steels is swamped by the rapid increase in ferrite volume fraction. For the as cast state, as more sulphides are able to precipitate at the interdendritic boundaries and austenite grain boundaries than in the solution treated condition, increasing the sulphur level causes a small deterioration in ductility at the high temperature end of the trough. In the present work, only narrow troughs have been found. This is in contrast to previous work on as cast C – Mn – Nb – Al steels, which exhibited wide troughs in the ductility curves, where it was shown that higher total sulphur levels lead to considerably worse ductility and that sulphur can be as detrimental to the ductility as niobium. It is recommended that, to avoid transverse cracking during continuous casting, in addition to keeping the sulphur level low, the carbon and manganese should also be as low as possible.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Magnetic Properties and Applications · Metallurgical Processes and Thermodynamics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Engineering and Mathematical Sciences City University, Northampton Square, London EC1 VOHB.

References (22)

Show source-provided references
1. MINTZ B. YUE S. and JONAS J. J.: Int. Mater. Rev. 1991 36 187–217.10.1179/imr.1991.36.1.187 ↗
2. MINTZ B.: ISIJ Int. 1999 36 833–855.10.2355/isijinternational.39.833 ↗
3. MINTZ B. and ABUSHOSHA R.: Mater. Sci Technol. 1992 8 171–177.10.1179/mst.1992.8.2.171 ↗
4. HANNERZ N. E.: Trans. Iron Steel Inst. Jpn 1985 25 149.10.2355/isijinternational1966.25.149 ↗
5. MINTZ B. and ARROWSMITH J. M.: Met. Technol. 1979 6 24–32.10.1179/030716979803276471 ↗
6. MINTZ B. ABUSHOSHA R. COMINELI O. G. and LOYOLADEOLIVIERA M. A.: Proc. Int. Conf. Thermec 97: ‘Thermomechanical processing of steels and other materials’ (ed. Chandra T. and Sakai T.) 867-887; 1997 Warrendale PA TMS.
7. ABUSHOSHA R., , VIPOND R., and MINTZ B.: Mater. Sci Technol., 1991,7, 1101-1107.
8. REVAUX T. BRICOT J. P. and OUDIN J.: J. Mater. Eng. Perform. 1996 5 260–268.10.1007/BF02650897 ↗
9. DEPREZ D. BRICOUT J. P. and OUDIN J.: J. Mater. Process Technol. 1992 32 325 — 334.10.1016/0924-0136(92)90189-Y ↗
10. KARJAILEN L. P. KINNUNEN H. and PORTER D.: in ‘Microalloying in steels’ (ed. J. M. Rodriguez-lbabe et al.) 477-483; 1998 Aedermannsdorf Switzerland Trans. Tech. Publications.
11. MINTZ B. MOHAMED Z. and ABUSHOSHA R.: Mater. Sci Technol. 1989 5 682–688.10.1179/mst.1989.5.7.682 ↗
12. OSIKOLU G. TACIKOWSKI M. and KOBYLANSKI A.: Mater. Sci. Technol. 1985 1 520–525.10.1179/026708385790124512 ↗
13. KOBASHI H.: Trans. Iron Steel Inst. Jpn 1991 31 268.10.2355/isijinternational.31.268 ↗
14. ABUSHOSHA R. AYYAD S. and MINTZ B.: Mater. Sci. Technol. 1998 14 227–235.10.1179/026708398790301593 ↗
15. MINTZ B. ABUSHOSHA R. and COWLEY A.: Mater. Sci Technol. 1998 14 222–226.10.1179/026708398790301584 ↗
16. COWLEY A., , ABUSHOSHA R., and MINTZ B.: Mater. Sci Technol., 1998, 14, 1145-1153.
17. TUKDOGAN E. T. IGNATOWICZ S. and PEARSON J.: J. Iron Steel Inst. 1955 180 349.
18. SUNDMAN B. JANSSON B. and ANDERSON J.-O.: Calphad 1985 9 3.10.1016/0364-5916(85)90021-5 ↗
19. 10.2355/tetsutohagane1955.87.8_55210.2355/tetsutohagane1955.87.8_552 ↗
20. CROWTHER D. N. and MINTZ B.: Mater. Sci. Technol 1986 2 671–676.10.1179/026708386790329019 ↗
21. LEWIS J. JONAS J. J. and MINTZ B.: ISIJ Int. 1998 38 300–309.10.2355/isijinternational.38.300 ↗
22. MINTZ B. LEWIS J. and JONAS J. J.: Mater. Sci Technol. 1997 13 379— 388.10.1179/026708397790302179 ↗