journal article·2016-03

Effect of Zr addition on toughness and microstructure of coarse grained heat affected zone in Al deoxidised low carbon steel

X. B. Li, Y. Min, C. J. Liu, M. F. Jiang

Materials Science and Technology· Volume 32· Issue 5
Publisher page

Abstract

The effect of Zr addition on the toughness and microstructure of coarse grained heat affected zone (CGHAZ) in Al deoxidised low carbon steel was investigated. In this present work, the specimens (Zr free and Zr added) were subjected to weld thermal cycle with heat input of 54, 80 and 100 kJ cm− 1 at 1350°C peak temperature using thermal simulator. The typical inclusions were characterised by scanning electron microscopy, and the chemical composition of the inclusions was determined by energy dispersive spectroscopy. The nanoscale precipitates were analysed by transmission electron microscopy and energy dispersive spectroscopy. It was verified that the occurrence of Zr in steel mostly exists in the form of oxide inclusions, but a few in the form of solid solution state and Zr containing precipitates when the concentration of Zr is 0.015. The improvement of CGHAZ toughness is obtained when the heat input is 80–100 kJ cm− 1. The possible reasons about the effects of Zr on the toughness of CGHAZ, including Zr containing inclusions, precipitates and microstructure characteristics, were also discussed.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Microstructure and Mechanical Properties of Steels · High-Temperature Coating Behaviors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Key Laboratory for Ecological Metallurgy of Multimetallic Mineral (Ministry of Education), School of Materials and Metallurgy, Northeastern University, Shenyang 110819, China

References (25)

Show source-provided references
1. 10.1179/1743284714Y.000000054910.1179/1743284714Y.0000000549 ↗
2. Takamura J., and Mizoguchi S. ‘Roles of oxides in steels performance’, Proc. 6th Int. Iron Steel Cong., Nagoya, the Iron and Steel Institute of Japan 1, 591–597; 1990.
3. 10.1016/j.matchar.2006.11.02810.1016/j.matchar.2006.11.028 ↗
4. 10.2355/isijinternational.54.18810.2355/isijinternational.54.188 ↗
5. 10.1016/j.msea.2013.11.02810.1016/j.msea.2013.11.028 ↗
6. 10.1016/S1006-7191(08)60042-310.1016/S1006-7191(08)60042-3 ↗
7. 10.2355/tetsutohagane1955.82.7_59310.2355/tetsutohagane1955.82.7_593 ↗
8. Chen Y. T. · Acta Metall. Sin · 2005 · 18 · 96
9. 10.2355/isijinternational.53.138610.2355/isijinternational.53.1386 ↗
10. 10.1179/174328471500Y.0000010210.1179/174328471500Y.00000102 ↗
11. 10.1179/1743284715Y.000000011010.1179/1743284715Y.0000000110 ↗
12. 10.1002/srin.20140051710.1002/srin.201400517 ↗
13. 10.1002/srin.20150016710.1002/srin.201500167 ↗
14. Feng Y. Y., Luo Z. A., Zhang D. H., Wei J., and Wang L. J. ‘The application of welding heat cycle computer software’, Proc. the Fifth International Conference on Physical and Numerical Simulation of Materials Processing, Zhengzhou, China 2785–2791; 2007.
15. 10.1016/0956-7151(92)90435-H10.1016/0956-7151(92)90435-H ↗
16. Krauss G. · Ferrite microstructure in continuously cooled low- and ultralow-carbon steels, ISIJ Int · 1995 · 35 · 937
17. 10.2355/isijinternational.49.106310.2355/isijinternational.49.1063 ↗
18. 10.2355/isijinternational.42.114410.2355/isijinternational.42.1144 ↗
19. 10.1179/mst.1994.10.5.35310.1179/mst.1994.10.5.353 ↗
20. 10.2355/isijinternational.43.111110.2355/isijinternational.43.1111 ↗
21. 10.1016/0921-5093(92)90381-A10.1016/0921-5093(92)90381-A ↗
22. 10.1016/S0921-5093(98)00804-110.1016/S0921-5093(98)00804-1 ↗
23. 10.2355/isijinternational.48.30110.2355/isijinternational.48.301 ↗
24. 10.2355/isijinternational.38.91310.2355/isijinternational.38.913 ↗
25. Li Y. Q. · Prog. Nat. Sci · 2000 · 10 · 331