journal article·2009-07

Welding repair by linear friction in titanium alloys

A. Mateo, M. Corzo, M. Anglada, J. Mendez, P. Villechaise, J.-P. Ferte, O. Roder

Materials Science and Technology· Volume 25· Issue 7
Publisher page

Abstract

Gas turbines for aeroengines are generally manufactured by attaching individual blades into slots in the disk. However, an alternative design consists in producing bladed disks, where disk and blades are a single piece. Previous studies have shown that linear friction welding is a technology which fits well for this application. On the other hand, bladed disks can experience in service damages and therefore affordable repair technology must be available. The present paper presents the microstructural and mechanical evaluation of double and triple welds produced to simulate replacements of damaged blades. The results show that, even though the successive welds induce a small strength decrease, both tensile and fatigue failures always initiated far away of the weld zone.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Titanium Alloys Microstructure and Properties · Fatigue and fracture mechanics

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Departament of Materials ScienceUniversitat Politècnica de Catalunya Av. Diagonal 647, Barcelona, Spain;, Email: antonio.manuel.mateo@upc.edu

Departament of Materials ScienceUniversitat Politècnica de Catalunya Av. Diagonal 647, Barcelona, Spain

Laboratoire de Mécanique et de Physique des Matériaux, Téleport 2 Avenue Clément Ader 86961, Futuroscope Chassenenuil Cedex, France

Snecma Welding Industrial Center Site de Villaroche Rond Point René Ravaud, Réau 77550 Moissy Cramayel, France

MTU Aero Engines GmbH Dachauer Strasse 665 80995 Muenchen, Germany

References (16)

Show source-provided references
1. EC: ‘Aeronautics for Europe’; 2000, Brussels, Office for Official Publications of the European Communitie s.
2. Esslinger J.: Proc. 10th Titanium World Conf. (ed.Lfifiering G., and Albrecht J.), Vol. V, 2837-2844; 2003, Munich, Wiley-VCH.
3. Roder O., Hem D., and Liitjering G.: 10th Titanium World Conf. (ed.Liitjering G., and Albrecht J.), Vol. V, 2867-2874; 2003, Munich, Wiley-VCH.
4. Broomfield R. W. ‘Designing with titanium’, 69-75; 1986, Bristol, Institute of Metals.
5. 10.1007/s11661-005-0335-510.1007/s11661-005-0335-5 ↗
6. ‘Welding titanium. A designers and users handbook’; 1999, Cambridge, TW I.
7. Corzo M., Mendez J., Villechaise P., Rebours C., Ferte J.P., Gach E., Roder O., Llanes L., Anglada M., and Mateo A.: Proc. 9th Int. Fatigue Cong.; 2006, Atlanta, GA, Elsevier.
8. 10.1007/s11661-001-1031-810.1007/s11661-001-1031-8 ↗
9. 10.1016/S0921-5093(99)00449-910.1016/S0921-5093(99)00449-9 ↗
10. 10.1016/S0921-5093(00)00914-X10.1016/S0921-5093(00)00914-X ↗
11. Helm D., and Lutjering G.: Proc. 9th World Conf. on ‘Titanium’, Gorynin I. V. and Ushkov S. S. Saint Petersburg, Russia, June 1999,1726–1733.
12. 10.3989/revmetalm.2005.v41.i6.23110.3989/revmetalm.2005.v41.i6.231 ↗
13. Lütjering G., and Williams J. C. ‘Titanium (engineering materials and processes)’, 224-232; 2003, Berlin, Springer-Verlag.10.1007/978-3-540-71398-2 ↗
14. Sauer C., and Lütjering G.: Mater. Set Eng. A, 2001, A319-321,393–397.10.1016/S0921-5093(01)01018-8 ↗
15. Wisbey A., Wallis I. C., Ubhi H. S., Sketchley P., Ward-Close C. M., and Thereadgill P. L.: Proc. 9th World Conf. on ‘Titanium’, Gorynin I. V. and Ushkov S. S. Saint Petersburg, Russia, June 1999,1718–1725.
16. Dieter G. E. ‘Mechanical metallurgy’; 1988, London, McGraw Hill.