journal article·2015-12

Analysis of residual stresses in particulate reinforced aluminium matrix composite after EDM

S. S. Sidhu, A. Batish, S. Kumar

Materials Science and Technology· Volume 31· Issue 15
Publisher page

Abstract

This paper reports the effect of properties of three types of particulate reinforced metal matrix composite materials (65 vol.-SiC/A356·2, 10 vol.--SiC–5 vol.- quartz/Al, 30 vol.-SiC/A359) and machining parameters on residual stresses induced in the machined surface during powder mixed electric discharge machining. Three electrode materials (Cu, Gr and Cu–Gr) and three machining parameters, namely, peak current and pulse (on/off) duration, are varied to determine the magnitude of induced residual stresses. The result shows that the workpiece, electrode material properties, and pulse off time significantly contribute in the formation of residual stresses. Concentration of reinforced particulates and matrix conductivity also play a vital role in the development of residual stresses. The deposition of disintegrated particles of composite electrode (Cu–Gr) results in high magnitude of residual stresses.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Machining and Optimization Techniques · Advanced Surface Polishing Techniques · Advanced machining processes and optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Mechanical Engineering, BCET, Gurdaspur, India

Department of Mechanical Engineering, Thapar University, Patiala, India

Department of Mechanical Engineering, Punjab Engineering College, Chandigarh, India

References (27)

Show source-provided references
1. 10.1080/1042691090276931910.1080/10426910902769319 ↗
2. 10.1016/j.jmatprotec.2004.04.32110.1016/j.jmatprotec.2004.04.321 ↗
3. 10.1007/s00170-008-1839-010.1007/s00170-008-1839-0 ↗
4. 10.1016/S0142-1123(01)00133-510.1016/S0142-1123(01)00133-5 ↗
5. 10.1016/S0924-0136(98)00082-X10.1016/S0924-0136(98)00082-X ↗
6. 10.1179/02670830110150998010.1179/026708301101509980 ↗
7. 10.1023/B:JMSC.0000021482.15837.fc10.1023/B:JMSC.0000021482.15837.fc ↗
8. 10.1107/S002188980402951610.1107/S0021889804029516 ↗
9. Fitzpatrick M. E., Fry A. T., Holdway P., Kandil L., Shackleton J., and Suominen L. ‘Measurement good practice guide no. 52. Determination of residual stresses by X-ray diffraction’, 2005.
10. 10.1081/MST-20005124410.1081/MST-200051244 ↗
11. 10.1016/S0007-8506(07)61694-110.1016/S0007-8506(07)61694-1 ↗
12. 10.1016/j.apsusc.2007.05.07810.1016/j.apsusc.2007.05.078 ↗
13. 10.1007/978-0-387-30877-710.1007/978-0-387-30877-7 ↗
14. Hauk V. ‘Structural and residual stress analysis by nondestructive methods: evaluation–application–assessment’; 1997, Elsevier.
15. 10.1016/j.jmatprotec.2008.09.03210.1016/j.jmatprotec.2008.09.032 ↗
16. Sikarskie D. · AIME Trans · 1967 · 239 · 577
17. Montgomery D. C. ‘Design and analysis of experiments’; 1997, New York, John Wiley and Sons.
18. Taguchi G. ‘Introduction to quality engineering’; 1990, Tokyo, Asian Productivity Organization.
19. Ross P. J. ‘Taguchi techniques for quality engineering’; 1996, New York, Mc-Graw Hill.
20. Kruth J. P., Lauwers B., Schacht B., Bleys P., and Stucki M. ‘Comparison between oil and water dielectric in wire EDM of tool steel’, Proc. 13th Int Symp. on ‘Electro-machining’ Bilbao, Spain May 2001, [conference organiser], 463–472.
21. Tvergaard V. · J. Am. Soc · 1993 · 76 · 729
22. 10.1016/j.jmapro.2010.10.00510.1016/j.jmapro.2010.10.005 ↗
23. 10.1016/j.ijpvp.2007.10.00710.1016/j.ijpvp.2007.10.007 ↗
24. 10.1016/S0167-577X(02)01436-210.1016/S0167-577X(02)01436-2 ↗
25. Trueman C. S. · J. Eur. Soc · 2000 · 20 · 629
26. 10.1016/j.jmatprotec.2005.02.21110.1016/j.jmatprotec.2005.02.211 ↗
27. 10.1016/S0924-0136(96)02730-610.1016/S0924-0136(96)02730-6 ↗