Microstructure and high temperature tensile properties of wide gap brazed cobalt based superalloy X-40
Source abstract
Abstract
Wide gap brazing (WGB) of X-40 cobalt based superalloy was conducted in this study using BNi-9 braze alloy with X-40 and IN738 additive alloys. A groove was machined into X-40 bars with a nominal width of 6·35 mm before filler application. Following brazing at 1200°C for 15 min, the microstructure of the as brazed joints was examined using SEM, EDS and nanoindentation technique. Both WGB joints with X-40 and IN783 additive alloys contained primary matrix phase in addition to a number of boron containing phases which assumed either eutectic or discrete forms. Nanoindention testing revealed that these boron containing phases exhibited hardness values several times higher than the base alloy and matrix phase contributing to the embrittlement of the braze joint. Porosity was also observed in both types of WGB braze joints, the degree of which was greatest in the braze joints with IN738 additive alloy. Tensile testing at 950°C showed that the yield strength of both WGB joints was higher than that of the baseline specimens while the ultimate tensile strength of the WGB joints was lower than that of the baseline X-40. The ductility of the WGB joints was significantly inferior to that of the baseline X-40, particularly for WGB with IN 738 additive alloy.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High Temperature Alloys and Creep · Intermetallics and Advanced Alloy Properties · High Entropy Alloys Studies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical and Aerospace EngineeringCarleton University, Ottawa, Ontario, Canada
Institute for Aerospace ResearchNational Research Council, Ottawa, Ontario, Canada
Liburdi Turbine ServicesDundas, Ontario, Canada
References (21)
Show source-provided references
1. Betteridge W. ‘Cobalt and its alloys’; 1982, Toronto, John Wiley & Sons Inc.
2. Jurgens W., and Malik M. P. ‘Wide gap brazing in the maintenance of turbine guide vanes’, 78-82,Vol. 98; 1985, Hamburg, Germany, DVS Berichte.
3. Gove K. · Met. Mater · 1989 · 5 · 341
4. 10.1179/mst.1985.1.8.60810.1179/mst.1985.1.8.608 ↗
5. Heikinheimo L. · Proc. VVT Symp., VTT Technical Research, Helsinki, Finland, 2001, Issue 211, · 149
6. Gandy D. W. · 2001
7. O'Neill W. M. · Proc. ASM Heat Treating Conf., St. Louis, MO, USA, October 2000, ASM Heat Treating Society · 1040
8. Demo W. A. · Adv. Mater. Process · 1992 · 3 · 43
9. Liburdi J., and Ellison K.: Proc. Int. Gas Turbine Aero Eng. Cong., 1993, ASME, 24-27, Cincinnati, Ohio.
10. McMurray J., and Miller J. Brazing filler metal composition and process, US Patent 4,394,347, July 19, 1983.
11. Miglietti W. M. · Proc. Int. Brazing Soldering Conf., Albuquerque, NM, USA, April 2000, American Welding Society, · 476
12. Au P., Dainty R. V., and Patnaik P. C.: in ‘Surface modification technologies III’, (ed.Sudarshan T. S., and Bhat D. G.), 729-748; 1990, Warrendale, PA, TMS.
13. 10.1016/S0924-0136(01)00831-710.1016/S0924-0136(01)00831-7 ↗
14. 10.1361/10549719977033572110.1361/105497199770335721 ↗
15. Kim Y. H. · Key Eng. Mater · 2005 · 297
16. 10.1016/S0924-0136(01)00596-910.1016/S0924-0136(01)00596-9 ↗
17. 10.1179/13621710422501217510.1179/136217104225012175 ↗
18. Henhoffer T., Huang X., Yandt S., Seo D., and Au P.: J. Mater. Set Technol., 2008, In press.
19. Miglietti W.: Proc. ASME Turbo. Expo. 2000, Munich, Germany, May 2000, International Gas Turbine Institute, paper no. 2000-GT-339.
20. Henhoffer T.: Master's dissertation, Carleton University, Ottawa, Ontario, Canada, April 2008.
21. Kott K., Nagy D., and Huang X.: Proc. 19th Canadian Mater. Sci. Conf., Met Soc, CIM, Hamilton, On, Canada, June 2007.