journal article·2000-07

Hot deformation behaviour of aluminium alloy 6061/SiC p MMCs made by powder metallurgy route

B.L. Zhang, M.S. Maclean, T.N. Baker

Materials Science and Technology· Volume 16· Issue 7-8
Publisher page

Abstract

The hot deformation behaviour of a 20 vol.-%SiC particle reinforced Al alloy 6061 composite and Al alloy 6061, made via a powder metallurgy (PM) route and treated by a T4 temper, were studied by compression testing over a range of temperatures (300–500°C)and at strain rates of 0.005, 0.05, and 0.09 s -1 . It was observed that the flow stresses of the composites were significantly higher than those of the alloy at lower deformation temperatures. However, the stress–strain curves of both the composite and the alloy showed significant softening during deformation at the lowest strain rate, the softening for the composite being faster than that of the alloy. The activation energy for hot deformation was determined for different strains, using a power law equation, and was found to change significantly with strain for both the alloy and the composite. This phenomenon was explained by the occurrence of dynamic precipitation and coarsening during deformation.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Advanced materials and composites · Microstructure and mechanical properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

University of StrathclydeGlasgow, G1 1XJ, UK

References (41)

Show source-provided references
1. 10.1179/imr.1994.39.1.110.1179/imr.1994.39.1.1 ↗
2. 10.1179/mst.1994.10.6.44310.1179/mst.1994.10.6.443 ↗
3. 10.1179/mst.1997.13.9.70910.1179/mst.1997.13.9.709 ↗
4. ARSENAULT R. J. WANG L. and FENG C. R.: Acta Metall Mater. 1991 39 47–57.10.1016/0956-7151(91)90327-W ↗
5. SUBRAMANIAN K. N., , BIELER T. R., , and LUCAS J. P., : Key Eng. Mater., 1995, 104-107, (1),157–213.
6. 10.1179/mst.1997.13.3.20310.1179/mst.1997.13.3.203 ↗
7. 10.1179/mst.1997.13.10.81810.1179/mst.1997.13.10.818 ↗
8. MCQUEEN H. J. and JONAS J. J.: in ‘Treatise on materials science and technology: plastic deformation of metals’ (ed. Arsenault R. J.) Vol. 6 393-493; 1975 New York Academic Press.10.1016/B978-0-12-341806-7.50014-3 ↗
9. ESPEDAL A., , GJESTLAND H., , RYUM N., , and MCQUEEN H. J.: Scand. J. Metall, 1989, 18, 131–136.
10. VERLINDEN B., and WOUTERS P.: Mater. Sct Eng. A, 1990, A123,229–237.
11. WOUTERS P., and VERLINDEN B.: Mater. Sct Eng. A, 1990, A123,239–245.
12. EVANGELISTA E., , FORCELLESE A., , GABRIELLI F., , and MENGUCCI P.: Int. J. Mater. Prod Technol, 1990, 1, 84–94.
13. 10.1016/0924-0136(90)90193-X10.1016/0924-0136(90)90193-X ↗
14. MCQUEEN H. J.: in ‘Hot deformation of aluminium alloys’ (ed. Langdon T. G. et al) 105-120; 1990 Warrendale PA TMS.
15. EVANGELISTA E. FORCELLESE A. GABRIELLI F. and MENGUCCI P.: in ‘Hot deformation of aluminium alloys’ (ed. Langdon T. G. et al) 121-139; 1990 Warrendale PA TMS.
16. EVANGELISTA E. MCQUEEN H. J. and CERRI E.: in ‘Modelling of plastic deformation and its engineering applications’ 265–270; 1992 Roskilde Denmark Rise) National Laboratory.
17. CERRI E., , EVANGELISTA E., , FORCELLESE A., , and MCQUEEN H. J.: Mater. Sct Eng. A, 1995, A197,181–198.
18. BLAZ L., and EVANGELISTA E.: Mater. Set Eng. A, 1996, A207,195–201.
19. NITH T. G.: Metall Trans. A, 1984, 15A, 139–146.10.1007/BF02644396 ↗
20. 10.1016/0956-716X(92)90316-710.1016/0956-716X(92)90316-7 ↗
21. 10.1179/mst.1994.10.6.48710.1179/mst.1994.10.6.487 ↗
22. 10.1179/02670839579016465210.1179/026708395790164652 ↗
23. 10.1080/17432847.1995.1194555610.1080/17432847.1995.11945556 ↗
24. 10.1016/0956-716X(95)00123-D10.1016/0956-716X(95)00123-D ↗
25. 10.1179/mst.1995.11.4.35710.1179/mst.1995.11.4.357 ↗
26. STYLES C. M. and PICTHER: Mater. Sct Technol 1998 14 913–919.10.1179/026708398790613605 ↗
27. 10.1179/mst.1998.14.9-10.105710.1179/mst.1998.14.9-10.1057 ↗
28. 10.1016/0956-716X(93)90496-F10.1016/0956-716X(93)90496-F ↗
29. VERLINDEN B. and VOITH K.: in ‘Numerical predictions of deformation processes and the behaviour of real materials’ (ed. Andersen S. I. et al) 601-606; 1995 Roskilde Denmark Riso National Laboratory.
30. RICHARDSON G. J. HAWKINS D. N. and SELLARS C. M.: ‘Worked examples in metalworking’ 1985 London The Institute of Metals.
31. RAZAGHIAN A. YU D. and CHANDRA T.: in ‘Advanced composites ‘93’ (ed. Chandra T. and Dhingra A. K.) 1067-1071; 1993 Warrendale PA TMS.
32. LIU Y., and BAKER T. N.: Mater. Sct Eng. A, 1995, A197,125–131.
33. EVANGELISTA E. GABRIELLI F. MENGUCCI P. and QUADRINI E.: in ‘Strength of metals and alloys’ (ed. Kettuen P. O. et al) 977-982; 1988 Pergamon.10.1016/B978-0-08-034804-9.50154-6 ↗
34. 10.1179/mst.1994.10.6.45210.1179/mst.1994.10.6.452 ↗
35. 10.1007/BF0285134910.1007/BF02851349 ↗
36. 10.1179/mst.1994.10.5.40610.1179/mst.1994.10.5.406 ↗
37. CHRISTMAN T. and SURESH S.: Acta Metall. 1988 36 1691–1704.10.1016/0001-6160(88)90236-2 ↗
38. 10.1016/0036-9748(89)90136-110.1016/0036-9748(89)90136-1 ↗
39. 10.1179/mst.1990.6.11.115710.1179/mst.1990.6.11.1157 ↗
40. MCQUEEN H. J.: in ‘Hot deformation of aluminium alloys’ (ed. Langdon T. G. et al) 31-54; 1990 Warrendale PA TMS.
41. MCQUEEN H. J., , EVANGELISTA E., , and KASSNER M. E.: Z. Metallkd., 1991, 82, 336–345.