Study on formation of surface and microstructure of stainless steel part produced by selective laser melting
Source abstract
Abstract
In order to further develop selective laser melting (SLM) technology, the formation of surface and microstructure of 316 stainless steel SLM parts was studied using optical microscopy and SEM, differential thermal analysis and thermal gravity analysis methods. Some effects such as heat transmission, energy distribution and rapid cooling and solidification during SLM process on the formation of surface and microstructure were mainly discussed. The results indicated that the surface morphology was affected by viscosity and fluidity of steel melts, which were governed by laser energy, heat transmission history and material properties, while porosity was influenced by surface morphology of each intermediate layer and the cooling rates of steel melts, which were determined by laser energy, heat transmission conditions and laser scanning history. The microstructures of 316 stainless steel SLM part were irregular non-equilibrium ones that converted to normal austenite after being heated at 627°C h–1.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Modern Manufacture Engineering CenterHeilongjiang University of Science and Technology, Harbin 150027, China;, Email: backmyself@163.com
State Key Laboratory of Materials Processing and Die and Mould TechnologySchool of Material Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, China
References (18)
Show source-provided references
1. 10.1016/j.ijmachtools.2006.09.01310.1016/j.ijmachtools.2006.09.013 ↗
2. 10.1016/S0890-6955(01)00093-110.1016/S0890-6955(01)00093-1 ↗
3. 10.1016/j.jmatprotec.2003.11.05110.1016/j.jmatprotec.2003.11.051 ↗
4. 10.1243/095440604131954510.1243/0954406041319545 ↗
5. 10.1023/B:JMSC.0000013875.62536.fa10.1023/B:JMSC.0000013875.62536.fa ↗
6. 10.1243/095440505X810910.1243/095440505X8109 ↗
7. 10.1243/095440505X3220110.1243/095440505X32201 ↗
8. 10.1023/A:101618560664210.1023/A:1016185606642 ↗
9. 10.1016/j.ics.2005.03.15510.1016/j.ics.2005.03.155 ↗
10. 10.1243/09544060376255466810.1243/095440603762554668 ↗
11. 10.1016/j.jmatprotec.2007.04.11710.1016/j.jmatprotec.2007.04.117 ↗
12. 10.1108/1355254081084152610.1108/13552540810841526 ↗
13. Nelson J. C. · ‘Selective laser sintering: a definition of the process and an empirical sintering model’ · 1993
14. Vitek J., David S., and Babu S.: Proc. 5th Int. Conf. on ‘Welding and repair technology for power plants’, Point Clear, AL, USA, June 2002, EPRI-RRAC, Paper GT10.
15. Gaümann M., Trivedi R., and Kurz W.: Mater. Sci Eng. A, 1997, A226-228,763–769.10.1016/S0921-5093(97)80081-0 ↗
16. 10.1016/0001-6160(86)90056-810.1016/0001-6160(86)90056-8 ↗
17. Gaümann M., Bezencon C., Canalis P., and Kurz W.: Acta Mater. 2001, 49, 1051–1062.10.1016/S1359-6454(00)00367-0 ↗
18. Vitek J. M.: Acta Mater. 2005, 53, (1), 53–67.10.1016/j.actamat.2004.08.039 ↗