journal article·2010-12

Influence of post-weld heat treatments on microstructure and mechanical properties of gas tungsten arc maraging steel weldments

V. Venkateswara Rao, G. Madhusudhan Reddy, A. V. Sitarama Raju

Materials Science and Technology· Volume 26· Issue 12
Publisher page

Abstract

The response to post-weld heat treatment of an 18%Ni (250 grade) gas tungsten arc weld metal has been investigated. The post-weld heat treatments are (a) direct aging at 480°C/3 h/air cooling, (b) solutionising at 815°C/1 h/air cooling+aging at 480°C/3 h/air cooling and (c) homogenisation at 1150°C/1 h/air cooling+solutionising at 815°C/1 h/air cooling+aging at 480°C/3 h/air cooling. Metallographic characterisation of fusion zone revealed pronounced segregation of titanium and molybdenum along the interdendritic and intercellular boundaries. This led, during subsequent aging, to austenite reversion at temperatures much lower than in wrought (unwelded) material. Solutionised treatment at 815°C does not remove the segregation. Homogenisation treatment (1150°C/1 h/air cooling) succeeded in making the composition become homogenised. Mechanical properties including tensile, hardness and impact toughness were evaluated. Tensile test results showed that directly aged weldments exhibited lower strength but higher ductility than the other cases; this was attributed to the presence of reverted austenite. Homogenisation at 1150°C/1 h/air cooling+solutionising at 815°C/1 h/air cooling+aging at 480°C/3 h/air cooling resulted in optimum tensile properties. A substantial increase in fusion zone toughness was observed after homogenisation+solutionising+aged condition due to a decrease in the content of austenite content compared to the directly aged condition. The reduction in microsegregation by diffusion of alloying elements from cell boundaries to the cell during homogenisation treatment is responsible for the decrease in austenite content.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Welding Techniques and Residual Stresses · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Advanced Systems LaboratoryHyderabad 500 058, India

Metal Joining GroupDefence Metallurgical Research Laboratory, Kanchanbagh, Hyderabad, Andhra Pradesh 500 058, India

Department of Mechanical EngineeringJawaharlal Nehru Technological University, Kakinada 533 003, India

References (20)

Show source-provided references
1. Muller G. P. · J. Iron Steel Inst · 1965 · 203 · 899
2. Perks M. D., and Kadonskii V. M. ‘High strength maraging steels’; 1970, Moscow, Metallurgy.
3. Lang F. H., and Kenyon N.: in ‘WRC Bulletin’,Vol. 159, ‘Welding of maraging steel’, 1971; New York, Welding Research Council, Engineering Foundation.
4. Boniszewski T. · Br. Weld. J · 1966 · 13 · 415
5. Duffy F. D., and Sutar W.: Weld. 1, 1965, 44, 251s-263s.
6. Wilson E. M. · Br. Weld. J · 1966 · 13 · 67
7. Nagarajan K. V. · Proc. Conf. on ‘Steels for engineering industries — trends in weldability’, Tiruchirapalli, India, 1998, Indian Institute of Metals, · 43
8. Canonico D. A. · Weld. J · 1964 · 10 · 433s
9. Kenyon N. · Weld. J · 1968 · 47 · 193s
10. Peterson W. A. · Weld. J. · 1964 · 43 · 428s
11. 10.1007/BF0265285810.1007/BF02652858 ↗
12. Allen N. P. · J. Iron Steel Inst · 1950 · 166 · 281
13. Sedriks A. J. · J. Iron Steel Inst · 1965 · 203 · 268
14. Paley Z. · Weld J. · 1969 · 48 · 245s
15. Ashirla Y. · Trans. Min. Metall. Assoc · 1981 · 19 · 483
16. Lee Y. M. ‘The study on autogenously welding of ultra high strength maraging steel’; 1988, Taipei, MST National Taiwan University.
17. 10.1179/13621710010153839910.1179/136217100101538399 ↗
18. Grong O. ‘Metallurgical modeling of welding’, 2nd edn; 1997, London, The Institute of Materials.
19. 10.1179/174328407X17977310.1179/174328407X179773 ↗
20. 10.1016/S0921-5093(98)00697-210.1016/S0921-5093(98)00697-2 ↗