journal article·2007-05

Dispersion strengthening in vanadium microalloyed steels processed by simulated thin slab casting and direct charging Part 1 – Processing parameters, mechanical properties and microstructure

Y. Li, J. A. Wilson, A. J. Craven, P. S. Mitchell, D. N. Crowther, T. N. Baker

Materials Science and Technology· Volume 23· Issue 5
Publisher page

Abstract

A study simulating thin slab continuous casting followed by direct charging into an equalisation furnace has been undertaken based on six low carbon (0·06 wt-%) vanadium microalloyed steels. Mechanical and impact test data showed that properties were similar or better than those obtained from similar microalloyed conventional thick cast as rolled slabs. The dispersion plus dislocation strengthening was estimated to be in the range 80–250 MPa. A detailed TEM/EELS analysis of the dispersion sized sub 15 nm particles showed that in all the steels, they were essentially nitrides with little crystalline carbon detected. In the steels V–Nb, V–Ti and V–Nb–Ti, mixed transition metal nitrides were present. Modelling of equilibrium precipitates in these steels, based on a modified version of ChemSage, predicted that only vanadium rich nitrides would precipitate in austenite but that the C/N ratio would increase through the two phase field and in ferrite. The experimental analytical data clearly point to the thin slab direct charging process, which has substantially higher cooling rates than conventional casting, nucleating non-equilibrium particles in ferrite which are close to stoichiometric nitrides. These did not coarsen during the final stages of processing, but retained their highly stable average size of, ∼7 nm resulting in substantial dispersion strengthening. The results are considered in conjunction with pertinent published literature.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Metal Alloys Wear and Properties · Metallurgy and Material Forming

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (61)

Show source-provided references
1. Orowan E.: Proc. Symp. on ‘Internal stresses in metals and alloys’, 451; 1948, London, Inst. Metals.
2. Ashby M. F. ‘Oxide dispersion strengthening’, (ed.Ansell G. S. et al), 143-205; 1958, Warrendale, PA, Met. Soc. AIME.
3. Gladman T., Holmes B., and McIvor I. D. ‘Effect of second phase particles on the mechanical properties of steel’, 68-78; 1971, London, Iron Steel Institute.
4. Gladman T. ‘The physical metallurgy of microalloyed steels’, 52; 1997, London, Inst. Materials.
5. 10.1088/0370-1301/64/9/30310.1088/0370-1301/64/9/303 ↗
6. Petch N. J. · J. Iron Steel Inst · 1953 · 174 · 25
7. Grozier J. D.: Proc. Conf. Microalloying ‘75, 241-250; 1977, New York, Union Carbide Corp.
8. 10.2355/isijinternational.42.63610.2355/isijinternational.42.636 ↗
9. 10.2355/isijinternational.44.109310.2355/isijinternational.44.1093 ↗
10. Kaspar R. · Met. Work · 1994 · 65 · 279
11. Kaspar R., and Pawelski O.: Proc. Int. METEC Cong., Dusseldorf, Germany, June 1994, VDEH,390–404.
12. Lubensky P. J., Wigman S. L., and Johnson D. J.: Proc. Conf. Microalloying ‘95, 225-233; 1995, Pittsburgh, PA, Iron & Steel Soc.
13. Leroy V., and Herman J. C.: Proc. Conf. Microalloying ‘95, 213-223; 1995, Pittsburgh, PA, Iron & Steel Soc.
14. Korchynsky M. · Scand. J. Metall · 1999 · 28 · 40
15. Crowther D. N., Li Y., Baker T. N., Green M. J. W., and Mitchell P. S. ‘Thermomechanical processing of steels’, 527-536; 2000, London, IOM.
16. 10.4028/www.scientific.net/MSF.284-286.51710.4028/www.scientific.net/MSF.284-286.517 ↗
17. Li Y. · IOP Conf. Ser · 2001 · 168 · 183
18. Wilson J. A. · IOP Conf. Ser · 2001 · 168 · 187
19. 10.1179/02670830422501674310.1179/026708304225016743 ↗
20. 10.4028/www.scientific.net/MSF.500-501.23710.4028/www.scientific.net/MSF.500-501.237 ↗
21. 10.1016/0001-6160(55)90090-010.1016/0001-6160(55)90090-0 ↗
22. Pickering F. B., and Gladman T. ‘Metallurical developments in carbon steels’, ISI Spec. Rep. no. 81, Iron Steel Inst., London, UK, 1963.
23. 10.1007/BF0268058010.1007/BF02680580 ↗
24. Morrison W. B., and Chapman J. A.: Proc. Rosenhain Centenary Conf., 286-303; 1976, London, The Royal Society.
25. Rose A. J. · 1998
26. 10.1016/0956-7151(92)90006-Z10.1016/0956-7151(92)90006-Z ↗
27. 10.1016/S1359-6454(00)00389-X10.1016/S1359-6454(00)00389-X ↗
28. 10.1007/BF0267075210.1007/BF02670752 ↗
29. 10.1016/0001-6160(81)90092-410.1016/0001-6160(81)90092-4 ↗
30. 10.1016/S1359-6454(96)00100-010.1016/S1359-6454(96)00100-0 ↗
31. Zajac S., Siwecki T., and Korchynsky M. ‘Low-carbon steels for the 90's’, (ed.Asfahani R., and Tither G.), 139-149; 1993, Warrendale, PA, TMS.
32. Goldschmidt H. J. ‘Interstitial alloys’, 238; 1957, London, Butterworths.
33. Douse K., and Baker T. N. ‘Thermomechanical processing of steels’, 573-580; 2000, London, IOM.
34. 10.1007/BF0058983510.1007/BF00589835 ↗
35. Poths R. M. · 2003
36. Baker T. N. ‘Yield, flow and fracture’, (ed.Baker T. N.), 235-273; 1983, London, New York, Applied Science Publishers.
37. Evans D. B. · Met. Soc. AIME · 1965
38. 10.2355/isijinternational1966.15.14510.2355/isijinternational1966.15.145 ↗
39. Siwecki T., Sandberg A., Roberts W., and Lagneborg R. ‘Themomechanical processing of austenite’, (ed. A. J. de Ardo et al), 163-194; 1982, Warrendale, PA, Met. Soc. AIME.
40. Vogels H. A. · Archiv. Eisenh · 1964 · 35 · 339
41. Baker T. N. · J. Iron Steel Inst · 1973 · 211 · 502
42. 10.1179/03071697480328807710.1179/030716974803288077 ↗
43. Houghton D. C., Weatherly G. C., and Embury J. D. ‘Themomechanical processing of austenite’, (ed. A. J. de Ardo et al), 267-292; 1982, Warrendale, PA, Met. Soc. TMS-AIME.
44. Roberts W. ‘TISLA steels, technology and applications’, (ed.Korchynsky M.), 33-65; 1984, Metals Park, OH, ASM.
45. 10.1016/0001-6160(85)90129-410.1016/0001-6160(85)90129-4 ↗
46. Sun F., and Cui W.: TISLA steels, processing, properties and technology’, (ed.Tither G., and Zhang S.), 43-50; 1992, Warrendale, PA, TMS-AIME.
47. Gladman T.: IISLA steels, processing, properties and technology’, (ed.Tither G., and Zhang S.), 3-14; 1992, Warrendale, PA, TMS-AIME.
48. Siwecki T., Sandberg A., and Roberts W.: TISLA steels, technology and applications’, (ed.Korchynsky M.), 619-634; 1984, Metals Park, OH, ASM.
49. He K. · Mater. Sci. Eng. A · 1993 · 169 · 5310.1016/0921-5093(93)90598-9 ↗
50. Bodnar R. L. · Iron Steelmaker · 1999 · 26 · 45
51. 10.1016/S1359-6462(00)00617-510.1016/S1359-6462(00)00617-5 ↗
52. Zajac S: Proc.43rd MWSP Conf.Vol. 29, 497-508; 2001, Warrendale, PA, ISS.
53. 10.1016/j.actamat.2005.03.03610.1016/j.actamat.2005.03.036 ↗
54. Rose A. ‘Modelling the precipitation in microalloyed steels’, British Steel Report SL/PM/R/S2971/4/97/A, UK, 1979.
55. Turkdogan E. T. · Trans ISS, Iron and Steelmaker · 1989 · 61 · 5
56. Roberts W. · 1980
57. 10.1007/BF0286895910.1007/BF02868959 ↗
58. Frohberg M. G. · Stahl und Eisen · 1960 · 80 · 359
59. Woodhead J. H.: Proc. Seminar on ‘Vanadium in high strength steel’, 3-10; 1979, London, VANITEC.
60. 10.1016/0956-7151(91)90121-G10.1016/0956-7151(91)90121-G ↗
61. Bucher J. H. · Am. Soc. Met. · 1965 · 5 · 1