journal article·2003-08

Microstructural characterisation of high velocity oxyfuel thermally sprayed Stellite 6

G. Kong, D. Zhang, P. D. Brown, D. G. McCartney, S. J. Harris

Materials Science and Technology· Volume 19· Issue 8
Publisher page

Abstract

High velocity oxyfuel (HVOF) thermal spraying with an oxygen-propylene combustion flame was used to deposit coatings of a Co–Cr–W–C alloy (similar in composition to Stellite 6) from gas atomised feedstock powder. The microstructural characteristics of the deposits were investigated using the combined techniques of X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). In particular, the tripod polishing technique was used to prepare large areas of electron transparent membrane for TEM analysis; these areas were typically of the order of several hundred square micrometres. Accordingly, SEM and TEM analysis could be directly correlated, providing a clear understanding of the overall nature of the coatings. The coatings exhibited characteristic splatlike, layered morphologies due to the deposition and resolidification ofmolten or semimolten powder particles. The as sprayed microstructure consisted of a face centred cubic Co rich metallic matrix with a small fraction of CoCr2O4 spinel oxide. The latter formed either as intersplat lamellae or intrasplat globules. Under the HVOF spray conditions employed, a high proportion of the feedstock powder appeared to have been fully melted prior to impact on the substrate, with partially or unmelted powder accounting for < 20% of the microstructure. Formation of the M7C3 phase, normally present in Stellite 6, appeared to have been suppressed by the high cooling rate during spray deposition.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Catalytic Processes in Materials Science

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. L. PAWLOWSKI: ‘The Science and engineering of thermal spray coatings’; 1995, Chichester, John Wiley & Sons.
2. SMITH R. W. · J. Mater., · 1995 · 47 · 32
3. 10.1557/mrs2000.11910.1557/mrs2000.119 ↗
4. NEVILLE A. · Proc. Inst. Mech. Eng., · 2000 · 214 · 41–48
5. ANTONY K. C. · J. Met., · 1983 · 35 · 52
6. 10.1115/1.345320310.1115/1.3453203 ↗
7. 10.1007/BF0265014010.1007/BF02650140 ↗
8. FRENK A. · Z Metallkd., · 1993 · 84 · 887
9. 10.1016/0043-1648(94)90089-210.1016/0043-1648(94)90089-2 ↗
10. 10.1016/0043-1648(87)90105-010.1016/0043-1648(87)90105-0 ↗
11. 10.1016/0043-1648(91)90106-510.1016/0043-1648(91)90106-5 ↗
12. AYACHE J. · UllrailliCYOSCOpy · 1995 · 60 · 195
13. 10.1361/10599630177034923110.1361/105996301770349231 ↗
14. 10.1007/BF0075220910.1007/BF00752209 ↗
15. 10.1016/0257-8972(91)90160-X10.1016/0257-8972(91)90160-X ↗
16. 10.1007/BF0240277610.1007/BF02402776 ↗
17. 10.1007/BF0266426710.1007/BF02664267 ↗
18. THOMPSON E. R. · Metall. Trans., · 1970 · 1 · 2799–2806
19. KUSOFFSKY A. · Calphacl · 1997 · 21
20. 10.1023/A:101858923025010.1023/A:1018589230250 ↗