Characterisation and quantification of cavities in 9Cr martensitic steel for power plants
Source abstract
Abstract
This work focuses on the characterisation of cavities evolution in a P91 steel pipe in three conditions: as received, and after creep at 650°C and 60 MPa for 7000 and 9000 h. A field emission gun scanning electron microscope (FEG-SEM) equipped with focused ion beam (FIB) gun, a conventional scanning electron microscope (SEM) and a light optical microscope (LOM) have been employed for the investigation. This study reveals two types of cavities: the pre-existing cavities, which are rare in this type of heat resistant steels, with a mean diameter of 2·56 μm and the cavities produced during creep with diameters smaller than 0·6 μm. Lath boundaries and precipitates are found to be preferential sites for cavity nucleation. Furthermore, the number density and volume fraction of these small cavities are calculated from 2D measurements and compared to 3D results obtained by FIB serial sectioning.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · High Temperature Alloys and Creep · Hydrogen embrittlement and corrosion behaviors in metals
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Institute for Materials Science and Welding, Graz University of Technology, Kopernikusgasse 24, A-8010 Graz, Austria
Centre for Materials Engineering, Department of Mechanical Engineering, University of Cape Town, Cape Town, South Africa
Materials Center Leoben Forschung GmbH (MCL), Roseggerstraße 12, A-8700 Leoben, Austria
References (27)
Show source-provided references
1. 10.1016/j.ijpvp.2010.03.01710.1016/j.ijpvp.2010.03.017 ↗
2. 10.1179/mht.2004.00610.1179/mht.2004.006 ↗
3. 10.1016/j.calphad.2007.04.00110.1016/j.calphad.2007.04.001 ↗
4. 10.1179/174892306X9973210.1179/174892306X99732 ↗
5. 10.1016/j.nucengdes.2007.02.00310.1016/j.nucengdes.2007.02.003 ↗
6. 10.1016/S0749-6419(02)00111-010.1016/S0749-6419(02)00111-0 ↗
7. 10.1007/BF0057039810.1007/BF00570398 ↗
8. 10.1016/j.matchar.2003.09.01210.1016/j.matchar.2003.09.012 ↗
9. Yadav SD, Rosc J, Sartory B, Brunner R, Sonderegger B, Sommitsch C and Poletti C: ‘Investigation of pre-existing pores in creep loaded 9Cr steel’, Proc. Conf. 2nd Int. Congress on ‘3D Materials science’, Annecy, France, 2014, TMS (The Minerals, Metals & Materials Society), 85–90.10.1002/9781118990278.ch14 ↗
10. 10.1016/j.msea.2006.05.01010.1016/j.msea.2006.05.010 ↗
11. 10.1016/j.msea.2010.07.02910.1016/j.msea.2010.07.029 ↗
12. 10.1016/j.msea.2012.12.00210.1016/j.msea.2012.12.002 ↗
13. 10.1016/j.actamat.2010.11.06510.1016/j.actamat.2010.11.065 ↗
14. 10.1016/j.matchar.2006.10.00110.1016/j.matchar.2006.10.001 ↗
15. Poletti C · Int. J. Mat. Res. · 2007 · 55 · 3875
16. Lasagni F · Act. Mater. · 2010 · 101 · 1151
17. 10.1115/1.144607610.1115/1.1446076 ↗
18. 10.1515/pm-2002-39120210.1515/pm-2002-391202 ↗
19. http://imagej.nih.gov/ij/download.html
20. 10.1016/j.jpowsour.2011.07.01010.1016/j.jpowsour.2011.07.010 ↗
21. Underwood EE: ‘Quantitative stereology’, 2nd edn, 109–113; 1970, Reading, MA, Addison-Wesley Publishing Company.
22. Schwartz HA · Met. Alloy. · 1934 · 5 · 139
23. Saltykov SA: ‘Stereometric metallography’, 2nd edn; 1958, Moscow, Metallurgizdat.
24. 10.1016/S0921-5093(97)00364-X10.1016/S0921-5093(97)00364-X ↗
25. 10.1016/j.msea.2013.07.02610.1016/j.msea.2013.07.026 ↗
26. 10.1007/s11661-997-0284-210.1007/s11661-997-0284-2 ↗
27. 10.1080/1478643590824326410.1080/14786435908243264 ↗