journal article·2001-05

Modification of residual stress by post-weld vibration

A.S.M.Y. Munsi, A.J. Waddell, C.A. Walker

Materials Science and Technology· Volume 17· Issue 5
Publisher page

Abstract

Previous studies have suggested that welding residual stresses can be reduced by the application of controlled vibration. In the present study welded specimens were processed after being cooled to room temperature, with varying amplitude of applied stress and time of vibration. An increase in the applied stress led to a significant decrease in the residual stresses. The effect of time of vibration was found to be very small for a lower range of applied stresses (<230 MPa); an increase in the time of vibration had no influence on residual stresses. At higher applied stresses (>230 MPa), the residual stresses were found to redistribute with increasing time of vibration. It is shown that the energy concept of the vibratory stress relief mechanism was not validated.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Advanced Welding Techniques Analysis · Advanced machining processes and optimization

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Glasgow Cledonian University G4 0BA, UK

The Department of Mechanical Engineering University of Strathclyde, Glasgow, Scotland (cwalker@mecheng.strath.ac.uk)

References (18)

Show source-provided references
1. AOKI S. and NISHIMURA T.: ‘Current topics in computational mechanics’ PVP Vol. 305: Proc. 1995 Joint ASME-JSME Pressure Vessels and Piping Conf. Honolulu HI USA July 1995 75–79; 1995 New York ASME.
2. AOKI S., , NISIMURA T., , HIROI T., , and AMANO Y.: Nippon Kikai Gakkai Ronbunshu, C (Trans. Jpn Soc. Mech. Eng., C), 1995, 61, 4800–4804.
3. MAEKAWA Y., , NAKAGIRI A., , and MAEDA H.: Nippon Kikai Gakkai Ronbunshu A, 1986, 52, 1295-1299.
4. MUNSI A. S. M. Y.: ‘Investigation and validation of vibratory methods for stress relieving and weld conditioning’, PhD thesis, University of Strathclyde, Glasgow, Scotland, February 1999.
5. MUNSI A. S. M. Y., , WADDELL A. J., , and WALKER C. A.: J. Mater. Design Appl., 2000, 214, 129–138.
6. NAKAGIRI A. H. MAEDA et al.: Nippon Kikai Gakkai Ronbunshu A 1984 50 751–757.
7. MILER H., and PFALZGRAF H. G.: Schweissen Schneiden, 1964, 16, 178–184.
8. SHANKER S. WOOD W. E. and KHAN K. H.: Proc. 12th Natl. SAMPE Tech. Conf. Seattle WA USA October 1980 776–786.
9. 10.1111/j.1460-2695.1996.tb01315.x10.1111/j.1460-2695.1996.tb01315.x ↗
10. WOZNEY G. P., and CRAWMER G. R.: Weld Res. (Suppl.), 1968, 23, 411–419.
11. HOUCK F.: Mech. Eng., 1966, 88, (9), 48–50.
12. BOTROS B. M.: ‘Residual stresses in welded steel structure - II’ SME Technical Paper (Series) MF80-305 Society of Manu-facturing Engineers Dearborn MI USA 1980.
13. RICH s. R.: Weld Eng., March 1969, 54, 44–45.
14. FENGHUA s., and DEXIN F.: J. Dalian Univ. Technol., 1994, 34, 390–393.
15. HEBEL G. JR.: Met. Prog., November 1985, 51–55.
16. CLAXTON R. A.: Verifact, 1983, 10, (1), 16–20.
17. CLAXTON R. A.: Verifact, 1983, 10, (2), 11–16.
18. CLAXTON R. A., and LUPTON A.: Weld. Met. Fabr., December 1991, 59, 541–544.