journal article·2004-02

Development and comparison of residual stress measurement on welds by various methods

Aruna Bahadur, B. Ravi Kumar, A. Seshu Kumar, G. G. Sarkar, J. S. Rao

Materials Science and Technology· Volume 20· Issue 2
Publisher page

Abstract

Residual stress constitutes an integral part of the total stress acting on any component in service. It is imperative to determine residual stress to estimate the life of critical engineering components, especially those that are welded. The stresses caused by non-uniform temperature distribution due to welding and the effect of these multiaxial stresses upon service performance are discussed. A controlled thermal severity test (CTS) was performed on mild steel plates bolted together, with anchor welds deposited on opposite sides. After cooling, bithermal and trithermal test welds were deposited one after the other. Varying welding stresses were deliberately introduced by using different thicknesses of both plates to change the thermal severity numbers (TSN). The main experimental technique used here to determine the magnitude and nature of residual stress is based on X-ray diffraction (XRD). It was utilised to develop and standardise other techniques. The XRD method is based on the peak shiftin the diffraction profile due to the presence of stress using a sin 2 ψ method. The peak shift is determined by orienting the sample at different angles ± ψ to the incident X-ray beam. The semidestructive technique of hole drilling and use of a strain gauge was also employed to determine residual stress in CTS specimens. The magnitude, nature, and direction of principal stresses were determined by relieving stresses through incremental blind hole drilling and measuring strain values at each step. The surface displacements arising due to hole drilling can also be determined by laser holography. A sandwich holography technique was developed to avoid unwanted rigid body motions of samples due to hole drilling when relieving stresses. Stress values were obtained by measuring fringe displacement between two exposures of a sandwich hologram, due to hole drilling. Results on the change in residual stress values with TSN are discussed. The residual stress values determined by XRD and sandwich holography were found to be comparable, and stress values obtained by hole drilling/strain gauge measurement were higher than these values. The reasons are discussed.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Welding Techniques and Residual Stresses · Microstructure and Mechanical Properties of Steels · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (24)

Show source-provided references
1. NOYAN L. C. and COHEN J. B.: ‘Residual stress measurement by X-ray diffraction and interpretation’ 1987; New York Springer Verlag.
2. RADAZ D.: ‘Heat effects of welding’ 200; 1992 Berlin Springer-Verlag.10.1007/978-3-642-48640-1 ↗
3. MADDOX S. J.: Met. Constr., 1985, 17, 220.
4. LINNERT C. E.: ‘Welding metallurgy’ 3rd edn Vol. 2 627; 1967 New York American Welding Society.
5. Measurement Group Tech Note TN 503-3 Residual Stress Measurement USA 1988.
6. 10.1179/mst.1992.8.3.21210.1179/mst.1992.8.3.212 ↗
7. Standard E 837-92 ASTM Philadelphia PA USA 1992.
8. 10.1111/j.1475-1305.1968.tb01353.x10.1111/j.1475-1305.1968.tb01353.x ↗
9. BEANEY I. M.: Strain, 1976, 99, 106.
10. ALLEN L. B.: Proc. SPIE 1960 July 713.
11. HAUK V. M., and MACHERAUCH E.: Adv. X-ray Anal., 1984,27, 81.
12. 10.1520/JTE11814J10.1520/JTE11814J ↗
13. CHIANG F. P. and KIN C. C.: J. Met. 1983 May 49.10.2307/1058115 ↗
14. MIDDLETON J. C.: NDT Int. 1987 20 (5) 291.10.1016/0308-9126(87)90447-0 ↗
15. 10.1007/BF0232614310.1007/BF02326143 ↗
16. FANINGER G.: J. Soc. Mater. ScL Jpn., 1970, 19, 42.
17. ESQUIVEL A. L.: Adv. X-ray Anal., 1969, 12, 269.
18. PRUMER R.: Proc. 6th Int. Conf. on NDT 1970 Hanover Germany.
19. 10.1154/S037603080001195210.1154/S0376030800011952 ↗
20. ABRAMSON N.: ‘The making and evaluation of holograms’ 1981; New York Academic Press.
21. 10.1364/AO.13.00201910.1364/AO.13.002019 ↗
22. 10.1364/AO.14.00098110.1364/AO.14.000981 ↗
23. CHANDLER H.: ‘Heat treaters guide’ 1995; ASM International.
24. WANG W., and XUEBAD H.: Trans. Chin. Weld Inst., 1989, 10, 181–187.