Fabrication and properties of metal matrix composites based on SiC fibre reinforced aluminium alloys
Source abstract
Abstract
Composites made with Al–7 wt-%Si alloys and discontinuous Nicalon SiC fibres were prepared by compocasting followed by squeeze casting. This technique gives rise to macroscopically homogeneous materials with, however, some segregation of the fibres in the eutectic phase, especially for the lowest volume fractions. The SiC fibres appreciably improve wear resistance, hardness, and compressive strength of the matrix, both in the as cast and heat treated conditions. An analysis of the compressive test results is given based on the mixture rule modified to apply for discontinuous randomly oriented fibre composites. However, it is shown that agreement between predictions and experimental results can only be obtained by considering the increase of the strength of the matrix as a result of the presence of the fibres. This increase is discussed in terms of structural changes and residual stresses created during cooling resulting from the difference in the coefficients of thermal expansion of the components.MST/732
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloys Composites Properties · Advanced ceramic materials synthesis · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. YAJIMA S. · Rev. Chim. Miner., · 1981 · 18 · 412
2. MARTINEAU P. · J. Mater. Sc · 1984, 19
3. MARTINEAU P. · J. Mater. Sc · 1984, 19
4. DIVECHA A. P. · J. Met., 1981, (9), 12-17.
5. 10.1007/BF0264439610.1007/BF02644396 ↗
6. K. OHORI, H. WATANABE and Y. TAKEUCHI: in Proc. Conf. on ‘Advanced materials research and developments for transport: composites’, (ed. P. Lamicq et al.), 233-239; 1985, Les Ulis, France, Les Editions de Physique.
7. A. SAKAMOTO, H. HASEGAWA and Y. MINODA: in Proc. Fifth Int. Conf. on ‘Composite materials’, ‘ICCM.V’, (ed. W. C. Harrigan et al), 699-707; 1985, Warrendale, PA, The Metallurgical Society of AIME.
8. 10.1007/BF0264415810.1007/BF02644158 ↗
9. MEHRABIAN R. · Light Met. (London) · 1975 · 11 · 177
10. 10.1007/BF0265271610.1007/BF02652716 ↗
11. 10.1007/BF0265992710.1007/BF02659927 ↗
12. 10.1007/BF0281201410.1007/BF02812014 ↗
13. 10.1007/BF0264241910.1007/BF02642419 ↗
14. 10.1007/BF0059148310.1007/BF00591483 ↗
15. 10.1016/0043-1648(84)90117-010.1016/0043-1648(84)90117-0 ↗
16. 10.1016/0022-0248(75)90233-X10.1016/0022-0248(75)90233-X ↗
17. CLOSSET B. · Trans. AFS · 1981 · 89 · 801
18. C. MILLIÈRE: PhD thesis, Institut National Polytechnique de Grenoble, 1986.
19. CHATTERJEE S. · Br. Foundryman · 1972 · 65 · 420
20. F. GIROT: PhD thesis, Universite de Bordeaux I, 1987.
21. 10.1179/mtlr.1965.10.1.110.1179/mtlr.1965.10.1.1 ↗
22. 10.1088/0508-3443/3/3/30210.1088/0508-3443/3/3/302 ↗
23. 10.1146/annurev.ms.10.080180.00130510.1146/annurev.ms.10.080180.001305 ↗
24. 10.1007/BF0055592910.1007/BF00555929 ↗
25. R. J. ARSENAULT and M. TAYA: in Proc. Fifth Int. Conf. on ‘Composite materials’, ‘ICCM.V', (ed. W. C. Harrigan et al.), 21-36; 1985, Warrendale, PA, The Metallurgical Society of AIME.