Optimization of the heat treatment strategy for Inconel 718 superalloy produced by laser powder bed fusion additive manufacturing process
Source abstract
Abstract
This study investigates the impact of heat treatments on the microstructure and mechanical properties of Inconel 718 components fabricated by Laser Powder Bed Fusion (LPBF). To address residual stresses and microstructural inhomogeneities caused by rapid thermal cycles, three sequential treatments homogenization heat treatment (HHT), solution heat treatment (SHT), and aging heat treatment (AHT) were applied. Using a multi-objective Response Surface Method (RSM), heat treatment parameters were optimized. HHT was conducted at 1080 °C for 1–8 h, followed by SHT (980–1140 °C for 1 h) and standard AHT. Results revealed that a 2-h HHT led to optimal mechanical performance and a refined, uniform microstructure by redistributing Nb and Ti precipitates from the γ-matrix, enhancing the alloy's strength and service capability.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Additive Manufacturing and 3D Printing Technologies · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, Motilal Nehru National Institute of Technology Allahabad, Prayagraj, UP, India
References (56)
Show source-provided references
1. 10.1016/j.msea.2017.02.06210.1016/j.msea.2017.02.062 ↗
2. 10.1007/s11837-016-2198-110.1007/s11837-016-2198-1 ↗
3. 10.1007/s11661-014-2722-210.1007/s11661-014-2722-2 ↗
4. 10.1016/j.jallcom.2011.10.10710.1016/j.jallcom.2011.10.107 ↗
5. 10.1016/j.promfg.2016.08.08910.1016/j.promfg.2016.08.089 ↗
6. 10.1016/j.msea.2015.05.00410.1016/j.msea.2015.05.004 ↗
7. 10.1016/j.msea.2011.09.02410.1016/j.msea.2011.09.024 ↗
8. 10.1016/j.jmatprotec.2018.02.03810.1016/j.jmatprotec.2018.02.038 ↗
9. 10.1177/0267083623121986510.1177/02670836231219865 ↗
10. 10.1007/s12008-024-01875-210.1007/s12008-024-01875-2 ↗
11. 10.1002/adem.20230081910.1002/adem.202300819 ↗
12. 10.1016/j.matpr.2023.09.09310.1016/j.matpr.2023.09.093 ↗
13. 10.1016/j.pmatsci.2017.10.00110.1016/j.pmatsci.2017.10.001 ↗
14. 10.1108/RPJ-07-2024-029310.1108/RPJ-07-2024-0293 ↗
15. 10.1007/s11665-019-03980-w10.1007/s11665-019-03980-w ↗
16. 10.1016/j.matdes.2020.10922810.1016/j.matdes.2020.109228 ↗
17. 10.1016/j.jmapro.2021.12.03310.1016/j.jmapro.2021.12.033 ↗
18. 10.1016/j.msea.2022.14386110.1016/j.msea.2022.143861 ↗
19. 10.1016/j.actamat.2019.11.05310.1016/j.actamat.2019.11.053 ↗
20. 10.1007/s11663-014-0054-710.1007/s11663-014-0054-7 ↗
21. 10.1016/j.addma.2018.12.01910.1016/j.addma.2018.12.019 ↗
22. Dwivedi A, Khurana MK, Bala YG. Heat-treated nickel alloys produced using Laser powder bed fusion-based additive manufacturing methods: a review. Chinese J Mech Eng Addit Manuf Front 2023; 2: 100087.
23. 10.1007/s12613-019-1740-x10.1007/s12613-019-1740-x ↗
24. 10.1016/j.scriptamat.2016.10.03510.1016/j.scriptamat.2016.10.035 ↗
25. 10.1016/j.actamat.2017.02.02510.1016/j.actamat.2017.02.025 ↗
26. Schneider J, Lund B, Fullen M. Effect of heat treatment variations on the mechanical properties of Inconel 718 selective laser melted specimens. Addit Manuf 2018; 21: 248–254.
27. 10.1002/crat.1970005011210.1002/crat.19700050112 ↗
28. 10.1016/j.msea.2015.05.03510.1016/j.msea.2015.05.035 ↗
29. 10.1016/j.msea.2011.11.09210.1016/j.msea.2011.11.092 ↗
30. 10.1016/j.jallcom.2018.06.11210.1016/j.jallcom.2018.06.112 ↗
31. 10.1007/s12613-020-1991-610.1007/s12613-020-1991-6 ↗
32. 10.1016/j.msea.2019.02.04610.1016/j.msea.2019.02.046 ↗
33. 10.1016/j.mtla.2020.10065710.1016/j.mtla.2020.100657 ↗
34. 10.1016/j.msea.2003.09.10010.1016/j.msea.2003.09.100 ↗
35. 10.1002/adem.20100023210.1002/adem.201000232 ↗
36. 10.1016/j.msea.2017.06.09810.1016/j.msea.2017.06.098 ↗
37. 10.1016/j.matdes.2016.09.08010.1016/j.matdes.2016.09.080 ↗
38. 10.1007/s11661-022-06867-z10.1007/s11661-022-06867-z ↗
39. Anderson H Carriere J Vaughn N et al. Design Expert Software; Stat-Ease Inc.: Minneapolis MN USA 2019. 2019; 2019.
40. 10.1016/j.msea.2019.13829410.1016/j.msea.2019.138294 ↗
41. 10.1016/j.msea.2018.03.07310.1016/j.msea.2018.03.073 ↗
42. Tucho WM, Ohm BA, Canizalez SAP, et al. Effects of δ Phase and Annealing Twins on Mechanical Properties and Impact Toughness of L-PBF Inconel 718. J Manuf Mater Process 2024; 8: 135.
43. 10.1016/j.msea.2019.03.10310.1016/j.msea.2019.03.103 ↗
44. 10.1088/0953-8984/24/9/09501010.1088/0953-8984/24/9/095010 ↗
45. 10.1007/s11661-020-05992-x10.1007/s11661-020-05992-x ↗
46. 10.1016/j.msea.2017.06.04510.1016/j.msea.2017.06.045 ↗
47. 10.1016/j.jmst.2023.11.03010.1016/j.jmst.2023.11.030 ↗
48. 10.3390/ma1302034010.3390/ma13020340 ↗
49. 10.1016/j.msea.2018.04.04510.1016/j.msea.2018.04.045 ↗
50. 10.1016/S1359-6462(98)00077-310.1016/S1359-6462(98)00077-3 ↗
51. 10.1016/j.actamat.2007.03.02110.1016/j.actamat.2007.03.021 ↗
52. 10.1016/j.matdes.2019.10791510.1016/j.matdes.2019.107915 ↗
53. 10.1016/j.matchar.2012.04.02010.1016/j.matchar.2012.04.020 ↗
54. 10.1016/j.actamat.2014.07.03610.1016/j.actamat.2014.07.036 ↗
55. 10.1016/j.msea.2019.13832710.1016/j.msea.2019.138327 ↗
56. 10.1016/j.jmst.2021.04.05910.1016/j.jmst.2021.04.059 ↗