journal article·2013-07

Effect of solidification rate on representative impurities distribution in Si–Cu alloy

M Fang, C H Lu, H X Lai, L Q Huang, J Chen, W H Ma, Z L Sheng, J N Shen, J T Li, X T Luo

Materials Science and Technology· Volume 29· Issue 7
Publisher page

Abstract

The main purpose of this article is to demonstrate that solvent refining in combination with directional solidification can be used for preparation of high purity metallurgical grade silicon for solar cells. Silicon was alloyed with copper and grew under different solidification rates from Si–Cu alloy melt. A detailed analysis of the microstructures and morphologies of Si–Cu alloy has been carried out, focusing on the distribution characteristic of representative impurities affected by solidification rate. The experimental results indicated that copper addition promotes segregation of metal impurities Fe, Al and Ca from metallurgical grade silicon, and the purification effect is more pronounced with the solidification rate decreases. It was also determined that the representative non-metallic impurity phosphorus has a remarkable separation performance after alloying with copper, which can be helpful for the phosphorus removal.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Silicon and Solar Cell Technologies · Semiconductor materials and interfaces · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Department of Materials Science and Engineering, Xiamen University, Xiamen 361005, China

National Engineering Laboratory for Vacuum Metallurgy, Faculty of Materials and Metallurgical Engineering, Kunming University of Science and Technology, Kunming 650093, China

Ningxia Electrical Power Ltd Co., Yinchuan 750002, China

References (24)

Show source-provided references
1. 10.1016/j.hydromet.2012.03.00710.1016/j.hydromet.2012.03.007 ↗
2. 10.1007/s11837-012-0383-410.1007/s11837-012-0383-4 ↗
3. 10.1016/j.jnoncrysol.2012.06.03110.1016/j.jnoncrysol.2012.06.031 ↗
4. 10.1016/S1003-6326(11)60873-X10.1016/S1003-6326(11)60873-X ↗
5. 10.1016/j.solmat.2011.02.00110.1016/j.solmat.2011.02.001 ↗
6. 10.1179/174328409X42894510.1179/174328409X428945 ↗
7. 10.1016/j.mseb.2010.11.01010.1016/j.mseb.2010.11.010 ↗
8. 10.1016/j.jmatprotec.2004.03.03510.1016/j.jmatprotec.2004.03.035 ↗
9. 10.1016/j.vacuum.2012.01.00410.1016/j.vacuum.2012.01.004 ↗
10. 10.1016/j.matlet.2012.03.03110.1016/j.matlet.2012.03.031 ↗
11. 10.1016/j.seppur.2011.09.00110.1016/j.seppur.2011.09.001 ↗
12. 10.1016/j.solmat.2007.07.01010.1016/j.solmat.2007.07.010 ↗
13. 10.2355/isijinternational.45.96710.2355/isijinternational.45.967 ↗
14. 10.1016/j.jcrysgro.2008.09.09510.1016/j.jcrysgro.2008.09.095 ↗
15. Esfahani S, Barati M:‘A novel purification method for production of sloar grade silicon’in ‘Materials challenges in alternative and renewable energy: ceramic transactions’(, Wicks G, et al.), 195–205; 2011, New York, John Wiley and Sons Ltd.10.1002/9781118019467.ch20 ↗
16. 10.1016/j.intermet.2012.02.00910.1016/j.intermet.2012.02.009 ↗
17. 10.1016/S0925-8388(00)00983-X10.1016/S0925-8388(00)00983-X ↗
18. 10.1007/s12633-009-9025-z10.1007/s12633-009-9025-z ↗
19. 10.1016/j.mssp.2004.06.00110.1016/j.mssp.2004.06.001 ↗
20. 10.1149/1.139359310.1149/1.1393593 ↗
21. 10.1016/j.mssp.2012.06.00910.1016/j.mssp.2012.06.009 ↗
22. 10.1002/9781118062111.ch7810.1002/9781118062111.ch78 ↗
23. 10.1016/j.jallcom.2006.04.04610.1016/j.jallcom.2006.04.046 ↗
24. Morita K: ‘Effects of Ca addition on the thermodynamic properties of P and B in molten silicon alloys’, Proc. 132nd ISS and TMS Conf. on ‘Modeling control and optimization in ferrous and non-ferrous industry’, San Diego, CA, USA, 2003, TMS, 49–60.