journal article·2023-11

Wire-arc additive manufactured Al–Cu alloy: Microstructure, mechanical properties and their anisotropy

Jiale Miao, Jiqiang Chen, Jieke Ren, Zhi Luo, Zhenglin Fan, Zixiang Zhou, Ting Xing, Renguo Guan

Materials Science and Technology· Volume 39· Issue 15
Publisher page

Abstract

The microstructure, mechanical properties and their anisotropies of wire-arc additive manufactured Al–Cu alloy at two different printing speeds were investigated, and post heat treatment is optimised. The results show that the grains are finer and the fraction of primary second phase is lower in the alloy prepared at the faster printing speed. The aging hardening response of the solution-treated sample is significantly faster than that of the direct-aging sample, and the peak hardness is higher. The mechanical properties of the as-deposited and T6-treated alloy both show anisotropy, and the latter one is more significant. The anisotropies are mainly attributed to the high porosity in inter-layer of the samples, and these pores are more significant for the T6-treated samples.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Aluminum Alloys Composites Properties · Additive Manufacturing and 3D Printing Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Faculty of Materials, Metallurgy and Chemistry, Jiangxi University of Science and Technology, Ganzhou, People's Republic of China

State Key Laboratory of Comprehensive Utilization of Low-Grade Refractory Gold Ores, Xiamen, People's Republic of China

Engineering Research Center of Continuous Extrusion, Ministry of Education, Dalian Jiaotong University, Dalian, People's Republic of China

Funding

National Natural Science Foundation of China · Natural Science Foundation of Jiangxi Province of China · Program of Qingjiang Excellent Young Talents of Jiangxi University of Science and Technology

References (40)

Show source-provided references
1. 10.1016/j.matchar.2022.11197710.1016/j.matchar.2022.111977 ↗
2. 10.1007/s00170-014-5808-510.1007/s00170-014-5808-5 ↗
3. 10.1016/j.commatsci.2011.06.02310.1016/j.commatsci.2011.06.023 ↗
4. 10.3390/ma1515546010.3390/ma15155460 ↗
5. 10.1007/s00170-015-7077-310.1007/s00170-015-7077-3 ↗
6. 10.1007/s40194-020-00959-310.1007/s40194-020-00959-3 ↗
7. 10.1016/S0924-0136(02)00257-110.1016/S0924-0136(02)00257-1 ↗
8. 10.1016/S0007-8506(07)60206-610.1016/S0007-8506(07)60206-6 ↗
9. 10.1080/02670836.2018.145501210.1080/02670836.2018.1455012 ↗
10. 10.1016/1044-5803(95)00066-610.1016/1044-5803(95)00066-6 ↗
11. 10.1002/ente.20180055010.1002/ente.201800550 ↗
12. 10.1088/1742-6596/2228/1/01202410.1088/1742-6596/2228/1/012024 ↗
13. 10.1007/s40194-017-0527-910.1007/s40194-017-0527-9 ↗
14. 10.1016/j.matchar.2017.11.05310.1016/j.matchar.2017.11.053 ↗
15. Chen J, Liu C, Li Q Stress aging of Al–Cu–Mg–Ag single crystal: The effect of the loading orientations. J Alloys Compd. 2020;49(7):128–132.
16. 10.1179/174328406X7929810.1179/174328406X79298 ↗
17. 10.1016/j.matlet.2009.12.03310.1016/j.matlet.2009.12.033 ↗
18. 10.2320/jinstmet.JD20160610.2320/jinstmet.JD201606 ↗
19. 10.2320/matertrans.L-M201782110.2320/matertrans.L-M2017821 ↗
20. 10.2320/matertrans.L-M201783710.2320/matertrans.L-M2017837 ↗
21. Owolabi GM, Thom M, Ajide O Warner fatigue responses of three AA 2000 series aluminum alloys. J Mater Sci Chem Eng. 2019;7(3):32–48.
22. 10.1016/0376-0421(95)00004-610.1016/0376-0421(95)00004-6 ↗
23. 10.1007/s12666-019-01731-y10.1007/s12666-019-01731-y ↗
24. 10.1016/j.jmst.2022.02.02410.1016/j.jmst.2022.02.024 ↗
25. 10.1016/j.jmrt.2022.09.05510.1016/j.jmrt.2022.09.055 ↗
26. 10.1016/j.jmst.2019.06.01610.1016/j.jmst.2019.06.016 ↗
27. Yu RZ, Zhao F, Yu SF Microstructure, properties and T6 heat treatment process optimization for wire arc additive manufacturing ER2319 aluminum deposited metals. Heat Treat Met. 2021;46(04):49–59.
28. 10.1016/S1003-6326(22)65830-810.1016/S1003-6326(22)65830-8 ↗
29. Yu J, Wang JJ, NiDR Microstructure and mechanical properties of additive manufactured 2319 alloy by electron beam freeform fabrication. Acta Metall Sinica. 2018;54(12):1725–1734.
30. 10.1016/j.msea.2004.08.02910.1016/j.msea.2004.08.029 ↗
31. 10.1016/j.matlet.2019.03.11210.1016/j.matlet.2019.03.112 ↗
32. 10.1016/j.matchar.2021.11119810.1016/j.matchar.2021.111198 ↗
33. 10.1016/j.msea.2015.09.12010.1016/j.msea.2015.09.120 ↗
34. 10.1016/j.matchar.2016.04.01710.1016/j.matchar.2016.04.017 ↗
35. 10.1007/s00170-020-05482-910.1007/s00170-020-05482-9 ↗
36. 10.1016/j.ijmecsci.2022.10783110.1016/j.ijmecsci.2022.107831 ↗
37. 10.3390/met1001007910.3390/met10010079 ↗
38. 10.1016/j.matdes.2022.11097410.1016/j.matdes.2022.110974 ↗
39. 10.1016/j.addma.2019.10090010.1016/j.addma.2019.100900 ↗
40. Xue CP, Zhang YX, Mao PC Improving mechanical properties of wire arc additively manufactured AA2196 Al–Li alloy by controlling solidification defects. Addit Manuf. 2021;43:102019.