journal article·2020-09

Creep behaviour of equiaxed fine-grain γ -TiAl-based alloy prepared by powder metallurgy

Zhenxin Duan, Ying Han, Xiaolei Song, Hua Chen

Materials Science and Technology· Volume 36· Issue 13
Publisher page

Abstract

In this study, γ-TiAl-based alloy with chemical composition of Ti–45Al–5Nb (in at.-%) fabricated by powder metallurgy method was crept at 700°C under 200–500 MPa. The creep properties and the microstructure after creep tests were investigated. The results showed that the γ-TiAl-based alloy was composed of equiaxed γ-TiAl grains and α 2 -Ti 3 Al grains with average sizes of 1.4 and 0.5 μm, respectively. The creep resistance deteriorated generally with increased applied stresses. The typical intergranular fracture characteristics were observed though the grains were small. The calculated stress exponent and activation energy revealed the main creep mechanism of grain boundary sliding. Furthermore, twinning and dynamic recrystallisation also led to the creep deformation.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Intermetallics and Advanced Alloy Properties · Advanced materials and composites · MXene and MAX Phase Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Key Laboratory of Advanced Structural Materials, Ministry of Education, School of Materials Science and Engineering, Changchun University of Technology, Changchun, People's Republic of China

Funding

National Natural Science Fund · Innovative Research Group Project of the National Natural Science Foundation of China

References (28)

Show source-provided references
1. 10.1016/j.pmatsci.2016.01.00110.1016/j.pmatsci.2016.01.001 ↗
2. 10.1016/j.msea.2016.09.09210.1016/j.msea.2016.09.092 ↗
3. 10.1016/j.intermet.2018.01.00610.1016/j.intermet.2018.01.006 ↗
4. 10.1080/09603409.2016.118306810.1080/09603409.2016.1183068 ↗
5. 10.1016/j.matdes.2015.06.09510.1016/j.matdes.2015.06.095 ↗
6. 10.1016/j.jallcom.2014.05.09210.1016/j.jallcom.2014.05.092 ↗
7. 10.1016/j.intermet.2014.01.01310.1016/j.intermet.2014.01.013 ↗
8. 10.1016/j.intermet.2010.08.02910.1016/j.intermet.2010.08.029 ↗
9. 10.1016/j.intermet.2013.07.00310.1016/j.intermet.2013.07.003 ↗
10. 10.1016/j.msea.2015.07.09210.1016/j.msea.2015.07.092 ↗
11. 10.1080/02670836.2017.132556310.1080/02670836.2017.1325563 ↗
12. 10.3390/ma1009110310.3390/ma10091103 ↗
13. 10.1016/j.msea.2017.11.08010.1016/j.msea.2017.11.080 ↗
14. 10.1016/j.jmst.2019.08.01010.1016/j.jmst.2019.08.010 ↗
15. 10.1016/j.intermet.2013.06.00610.1016/j.intermet.2013.06.006 ↗
16. 10.1016/j.intermet.2012.07.02210.1016/j.intermet.2012.07.022 ↗
17. 10.1016/j.intermet.2004.09.00110.1016/j.intermet.2004.09.001 ↗
18. 10.1016/j.intermet.2013.10.01910.1016/j.intermet.2013.10.019 ↗
19. 10.1016/j.msea.2008.11.07110.1016/j.msea.2008.11.071 ↗
20. 10.4028/www.scientific.net/MSF.816.57210.4028/www.scientific.net/MSF.816.572 ↗
21. 10.1016/j.actamat.2003.10.01810.1016/j.actamat.2003.10.018 ↗
22. 10.1016/j.scriptamat.2004.08.02710.1016/j.scriptamat.2004.08.027 ↗
23. 10.1016/0956-716X(94)90050-710.1016/0956-716X(94)90050-7 ↗
24. 10.1016/j.msea.2009.03.08010.1016/j.msea.2009.03.080 ↗
25. 10.1016/S0966-9795(98)00117-410.1016/S0966-9795(98)00117-4 ↗
26. 10.1038/nmat467710.1038/nmat4677 ↗
27. 10.1016/j.msea.2004.01.12410.1016/j.msea.2004.01.124 ↗
28. 10.1016/j.msea.2015.03.05910.1016/j.msea.2015.03.059 ↗