Characteristics of pure-titanium and low carbon steel friction-welded joint with post-weld heat-treatment
Source abstract
Abstract
The characteristics of friction-welded joint between commercially pure-titanium (CP-Ti) and low carbon steel, of which was subjected to post-weld heat-treatment (PWHT), was investigated. When the joint was made with friction speed of 25 s −1 , friction pressure of 200 MPa, friction time of 2.5 s and forge pressure of 250 MPa, it had the same tensile strength as that of the CP-Ti base metal. The joint had no intermediate layer consisting of intermetallic compound (IMC interlayer) at the weld interface. The joint efficiency of the joint subjected to PWHT decreased with increasing heating temperature and its holding time, and the joint fractured at the weld interface although it had no IMC interlayer. The void was generated on the weld interface of the joint during PWHT process.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Advanced Welding Techniques Analysis · Intermetallics and Advanced Alloy Properties · Welding Techniques and Residual Stresses
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Engineering, Graduate School of Engineering, University of Hyogo, 2167 Shosha, Himeji, Hyogo 671-2280, Japan
Department of Mechanical Engineering, Faculty of Engineering, Kitami Institute of Technology, 165 Koen-cho, Kitami, Hokkaido 090-8507, Japan
References (45)
Show source-provided references
1. American Welding Society: ‘Welding handbook’, 7th edn, Vol. 4, 537–538; 1982, Miami, FL, American Welding Society.
2. Murti K. G. K., and Sundaresan S.: ‘Thermal behavior of austenitic-ferritic transition joints made by friction welding’, Weld. J. (suppl.), 1985, 64, (12), 327s–334s.
3. Ochi H., , Ogawa K., , Yamamoto Y., and Suga Y.: ‘Effect of heat treatment on friction welded joint strength of 6061 aluminum alloy to SUS304 stainless steel', J. Japanese Soc. Str. Frac. Mat., 1998, 32, (2), 43–50 (in Japanese).
4. Li H. Y., , Huang Z. W., , Bray S., , Baxter G., and Browen P.: ‘High temperature fatigue of friction welded joints in dissimilar nickel based super alloys', Mater. Sci. Technol., 2007, 23, (12), 1408–1418.
5. Feng A. H., , Xiao B. L., and Ma Z. Y.: ‘Effect of micro structural evolution on mechanical properties of friction stir welded AA2009/SiCp composite', Compos. Sci. Technol., 2008, 68, (9), 2141–2148.
6. Hassan A. S., , Mahmoud T. S., , Mahmoud F. H., and Khalifa T. A.: ‘Friction stir welding of dissimilar A319 and A356 aluminium cast alloys', Sci. Technol. Weld. Join., 2010, 15, (5), 414–422.
7. Krishnan M. M., and Marimuthu K.: ‘Effect of post-weld heat treatment on dissimilar friction stir welded AA6063 and A319 aluminum alloys', Int. J. Mater. Res., 2014, 105, (5), 507–511.
8. Mousavi S. A. A. A., and Sartangi P. F.: ‘Effect of post-weld heat treatment on the interface micro structure of explosively welded titanium-stainless steel composite', Mater. Sci. Eng. A, 2008, 494, 329–336.
9. Hsieh C. T., , Chu C. Y., , Shiue R. K., and Tsay L. W.: ‘The effect of post-weld heat treatment on the noched tensile fracture of Ti-6Al-4V to Ti-6Al-6V-2Sn dissimilar laser welds', Mater. Des., 2014, 59, 227–232.
10. Chu C. Y., , Hsieh C. T., and Tsay L. W.: ‘Microstructure and notched tensile fracture of Ti-6Al-4V to Ti-4.5Al-3V-2Fe-2Mo dissimilar welds', Mater. Des., 2014, 63, 14–19.
11. Serizawa H., , Mori D., , Ogiwara H., and Mori H.: ‘Effect of laser beam position on mechanical properties of F82H/SUS316L butt-joint welded by fiber laser', Fusion Eng. Des., 2014, 89, (7/8), 1764–1768.
12. Albert S. K., , Das C. R., , Sam S., , Mastanaish P., , Patel M., , Bhaduri A. K., , Jayakumar T., , Murthy C. V. S., and Kumar R.: ‘Mechanical properties of similar and dissimilar weldments of RAFMS and AISI 316l (N) SS prepared by electron beam welding process', Fusion Eng. Des., 2014, 89, (7/8), 1605–1610.
13. Sarafan S., , Wanjara P., , Champliaud H., and Thibault D.: ‘Characteristics of an autogenous single pass electron beam weld in thick gage CA6NM steel', Int. J. Adv. Manuf. Technol., 2014, 78, (9/12), 1523–1535.
14. Bhaduri A. K., , Rai S. K., , Gill T. P. S., , Sujith S., and Jayakumar T.: ‘Evaluation of repair welding procedures for 2.25Cr-1Mo and 9Cr-1Mo steel welds', Sci. Technol. Weld. Join., 2011, 6, (2), 89–93.
15. Dong H., , Yang L., , Dong C., and Kou S.: ‘Improving arc joining of Al to steel and Al to stainless steel', Mater. Sci. Eng. A, 2012, 534, 424–435.
16. Chen G., , Zhang Q., , Liu J., , Wang J., , Yu X., , Hua J., , Bai X., , Zhang T., , Zhang J., and Tang W.: ‘Microstructures and mechanical properties of T92/Super 304H dissimilar steel weld joints after high-temperature ageing', Mater. Des., 2013, 44, 469–475.
17. Wang K. K.: ‘Friction Welding' Welding Research Council Bulletins 1975 WRC Bulletin 204 1–21.
18. Japan Friction Welding Association: ‘Friction welding’, 6–14; 1979, Tokyo, Corona Publishing (in Japanese).
19. Kim Y. C., and Bang H. S.: ‘The general conditions which the reheat cracking test specimen must have', Q. J. Jpn. Weld. Soc., 2001, 19, (1), 148–155 (in Japanese).
20. Kim Y. R., and Kim J. W.: ‘A study on the thermal stress analysis of thick plate structures in post weld heat treatment', Int. J. Precis. Eng. Manuf., 2013, 14, (2), 247–252.
21. Fuji A., , Ameyama K., and North T. H.: ‘Improved mechanical properties in dissimilar Ti-AISI 304L joints', J. Mater. Sci., 1996, 31, (3), 819–827.
22. Fuji A.: ‘In situ observation of interlayer growth during heat treatment of friction weld joint between pure titanium and pure aluminium', Sci. Technol. Weld. Join., 2002, 7, (6), 413–416.
23. Fuji A., , Ikeuchi K., , Sato Y. S., and Kokawa H.: ‘Interlayer growth at interfaces of Ti/Al-1%Mn, Ti/Al-4.6%Mg and Ti/pure Al friction weld joints by post-weld heat treatment', Sci. Technol. Weld. Join., 2004, 9, (6), 507–512.
24. 10.1179/174329305X4059810.1179/174329305X40598 ↗
25. 10.1179/13621710422501716610.1179/136217104225017166 ↗
26. Kimura M., , Ishii H., , Kusaka M., , Kaizu K., and Fuji A.: ‘Joining phenomena and joint strength of friction welded joint between pure aluminium and low carbon steel', Sci. Technol. Weld. Join., 2009, 14, (5), 388–395.
27. Kimura M., , Kusaka M., , Kaizu K., and Fuji A.: ‘Effect of post-weld heat treatment on joint properties of friction welded joint between brass and low carbon steel', Sci. Technol. Weld. Join., 2010, 15, (7), 590–596.
28. Kimura M., , Fuji A., , Konno Y., , Itoh S., and Kim Y. C.: ‘Investigation of fracture for friction welded joint between pure nickel and pure aluminium with post-weld heat treatment', Mater. Des., 2014, 57, 503–509.
29. Kimura M., , Fuji A., and Shibata S.: ‘Joint properties of friction welded joint between pure magnesium and pure aluminium with post-weld heat treatment', Mater. Des., 2015, 85, 169–179.
30. Hasui A., and Kira Y.: ‘Friction welding of Titanium and plain carbon steel', Q. J. Jpn. Weld. Soc., 1983, 1, (3), 366–371 (in Japanese).
31. Shinoda T., and Takegami H.: ‘Friction welding of titanium and carbon steel', Proc. 1999 National Symp. Weld. Mech. Des. Jpn. Weld. Soc., Osaka, December 1999, 247–254 (in Japanese).
32. 10.1016/j.jmatprotec.2006.11.12310.1016/j.jmatprotec.2006.11.123 ↗
33. Kimura M., , Iijima T., , Kusaka M., , Kaizu K., and Fuji A.: ‘Joining phenomena and tensile strength of friction welded joint between pure titanium and low carbon steel', Mater. Des., 2014, 55, 152–164.
34. Dong H., , Yu L., , Deng D., , Zhou W., and Dong C.: ‘Direct friction welding of TiAl alloy to 42CrMo steel rods', Mater. Manuf. Process., 2015, 30, (9), 1104–1108.
35. Japan Institute of Metals: ‘Metals data book’, 4th edn, 508; 2008, Tokyo, Maruzen Publishing (in Japanese).
36. Larson F. R., and Miller A. A.: ‘Time-temperature relationship for rupture and creep stress', Trans. Am. Soc. Mech. Eng., 1952, 74, (7), 765–775.
37. David C., , Panigrahi B. K., , Balaji S., , Balamurugan A. K., , Nair K. G. M., , Amarendra G., , Sundar C. S., and Raj B.: ‘A study of the effect of titanium on the void swelling behavior of D9 steels by ion beam simulation', J. Nucl. Mater., 2008, 383, 132–136.
38. Japan Institute of Metals: ‘Metals data book’, 4th edn, 20–25; 2008, Tokyo, Maruzen Publishing (in Japanese).
39. Nagaoka T., , Mizuuchi K., , Sugioka M., and Fukusumi M.: ‘Plused current hot pressing of Chromium-plated SUS304L stainless steel and Titanium', J. Jpn. Inst. Metals, 2005, 69, (8), 727–730 (in Japanese).
40. Ghosh M., , Das S., , Banarjee P. S., and Chatterjee S.: ‘Variation in the reaction zone and its effects on the strength of diffusion bonded titanium-stainless steel couple', Mater. Sci. Eng. A, 2005, 390, 217–226.
41. 10.2207/qjjws.6.10410.2207/qjjws.6.104 ↗
42. Nishi H., , Araki T., and Eto M.: ‘Diffusion bonding of alumina dispersion-strengthened copper to 316 stainless steel with interlayer metals', Fusion Eng. Des., 1998, 39-40, 505–511.
43. Wang Q., , Leng X. S., , Yang T. H., and Yan J. C.: ‘Effects of Fe-Al intermetallic compounds on interfacial bonding of clad materials', Trans. Nonferrous Met. Soc. China, 2014, 24, (1), 279–284.
44. Ishikawa S., , Hayashi H., , Suenaga M., and Ohno Y.: ‘Formation of kirkendall voids in the reactive diffusion between Cu plate and lead-rich solders', Jpn. Inst. Electronics Packaging, 2006, 9, (4), 267–277 (in Japanese).
45. Springer H., , Kostka A., , dos Santos J. F., and Raabe D.: ‘Influence of intermetallic phases and kirkendall-porosity on the mechanical properties of joints between steel and aluminium alloys', Mater. Sci. Eng. A, 2011, 528, (13/14), 4630–4642.