Effect of microstructure on electrical conductivity of Inconel 718 alloys
Source abstract
Abstract
The microstructural evolution of Inconel 718 during aging processes has been studied through a combination of eddy current testing, X-ray diffraction analysis, and metallography and hardness measurements. Measurements were carried out in samples subjected to eight different heat treatment cycles, between 620 and 1035°C for 1–18 h. Different amounts of secondary precipitates were achieved, reaching 18 of delta phase for samples overaged at 900°C for 18 h. Results show that the different microstructures of Inconel 718 obtained have a distinguishable effect on electrical conductivity when this is measured through an appropriately sensitive technique (i.e. eddy current testing). The lowest conductivity values were observed for under aged samples (1·44 IACS). A clear increase in conductivity values was seen for all aged or overaged conditions, reaching a maximum of 1·63 IACS, when coarsening of intra granular precipitates, associated with an increase in density of globular precipitates at grain boundaries, was identified. The influence of microstructure on conductivity could be shown to be due to the competition between two effects on the scattering of electrons: matrix purification and precipitation characteristics. A combination of hardness values and electrical properties proved to be a fast and practical way of determining the stage of aging of the alloy.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Welding Techniques and Residual Stresses · Non-Destructive Testing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Post-graduation Program in Mining, Metallurgical and Materials Engineering (PPGE3M), Federal University of Rio Grande do Sul (UFRGS), Porto Alegre, Brazil
University of Bremen, Bremen, Germany
References (39)
Show source-provided references
1. McCoy SA, Puckett BC and Hibnerx EL: unpublished work; 2011, Beechwood, OH, Special Metals Wiggin Ltd.
2. 10.1007/s11837-006-0079-810.1007/s11837-006-0079-8 ↗
3. 10.1016/S0921-5093(01)01881-010.1016/S0921-5093(01)01881-0 ↗
4. 10.1007/BF0264960410.1007/BF02649604 ↗
5. 10.1016/S0921-5093(99)00235-X10.1016/S0921-5093(99)00235-X ↗
6. 10.7449/2001/Superalloys_2001_617_62610.7449/2001/Superalloys_2001_617_626 ↗
7. Cai DY · Trans. Nonferrous Met. Soc. · 2003 · 13 · 1338
8. 10.1016/j.matchar.2009.10.00310.1016/j.matchar.2009.10.003 ↗
9. Anon: ‘Specification of nickel base alloy 718 (UNS N07718) for oil and gas drilling and production’, API specification 6A718, 1st edn; 2004, Washington, DC, American Petrolium Institute. 1–17.
10. 10.1007/BF0264754910.1007/BF02647549 ↗
11. 10.1016/S0924-0136(97)00429-910.1016/S0924-0136(97)00429-9 ↗
12. 10.1016/j.optlastec.2013.09.03010.1016/j.optlastec.2013.09.030 ↗
13. 10.1016/j.matchar.2013.04.01810.1016/j.matchar.2013.04.018 ↗
14. 10.1179/1743284713Y.000000035810.1179/1743284713Y.0000000358 ↗
15. 10.1007/s10921-010-0072-610.1007/s10921-010-0072-6 ↗
16. Yu F · J. Nondestruct. Eval. · 2006 · 25 · 17
17. 10.1016/j.nucengdes.2006.02.01110.1016/j.nucengdes.2006.02.011 ↗
18. 10.1016/j.nucengdes.2005.01.00510.1016/j.nucengdes.2005.01.005 ↗
19. 10.1016/j.matdes.2013.03.04010.1016/j.matdes.2013.03.040 ↗
20. 10.1016/j.jmatprotec.2007.09.00310.1016/j.jmatprotec.2007.09.003 ↗
21. 10.1016/j.msea.2007.02.00610.1016/j.msea.2007.02.006 ↗
22. Pellegrini HV · Met. Prog. · 1980 · 117 · 60
23. Vietz JT: ‘The use of eddy current conductivity measurements for checking and predicting the strength of heat-treated aluminium alloys’, 8, 4 l. 1967, Melbourne, Department of Supply, Australian Defence Scientific Service, Aeronautical Research Laboratories.
24. Seppi F · Mater. Eval. · 1986 · 44 · 27
25. 10.4028/www.scientific.net/MSF.706-709.240610.4028/www.scientific.net/MSF.706-709.2406 ↗
26. 10.1007/s11661-010-0483-010.1007/s11661-010-0483-0 ↗
27. Parthasarathy TA · Stud. Appl. Electromagn. Mech. · 2010 · 33 · 165
28. 10.1007/s11837-012-0234-310.1007/s11837-012-0234-3 ↗
29. Xie XS, Xu CM, Wang GL, Dong JX, Ca WD and Kennedy R: ‘TTT diagram of a newly developed nickel-base superalloy – Allvac (R) 718Plus (TM)’, in ‘Superalloys 718, 625, 706 and derivatives’, 193–202; 2005, Warrendale, PA, TMS.10.7449/2005/Superalloys_2005_193_202 ↗
30. Anon. ‘Standard practice for electrolytic extraction of phases from Ni and Ni–Fe base superalloys using a hydrochloric-methanol electrolyte’, 2010, ASTM International, West Conshohocken, PA, USA, 2010.
31. Anon. ‘Standard test methods for determining average grain size, ASTM International E 112, ASTM International, West Conshohocken, PA, USA, 2012, 1–27.
32. Anon: ‘ASM specialty handbook: nickel, cobalt, and their alloys’; 2000, Materials Park, OH, ASM International.
33. 10.1016/S0925-8388(00)00789-110.1016/S0925-8388(00)00789-1 ↗
34. 10.1016/j.jallcom.2009.07.04610.1016/j.jallcom.2009.07.046 ↗
35. 10.1016/j.matchar.2004.07.00410.1016/j.matchar.2004.07.004 ↗
36. 10.1007/BF0264925910.1007/BF02649259 ↗
37. 10.1007/BF0266757810.1007/BF02667578 ↗
38. 10.1016/0001-6160(85)90211-110.1016/0001-6160(85)90211-1 ↗
39. 10.1016/S1359-6462(97)00064-X10.1016/S1359-6462(97)00064-X ↗