High-strain-rate deformation behaviour of new high-Mn austenitic steel during impact shock-loading
Source abstract
Abstract
The influence of impact shock-loading was investigated on the mechanical behaviour, microstructure evolution, and texture of a new high-Mn steel. The mechanical behaviour of the shock-loaded specimen was compared with quasi-static compression condition. A Hopkinson pressure bar setup was used to perform the high-strain-rate deformation. Continuous yielding was observed under both low and high-strain-rate deformation. The yield stress also illustrated a positive strain-rate sensitivity with increasing strain-rate. An obvious increase in the flow stress of the steel was detected at higher strain-rate. A strain hardening followed by a strain softening was detected in stress–strain curve after shock-loading. Electron backscatter diffraction also displayed the activation of strain-induced ϵ-martensite and ά-martensite while deformation twinning was absent at high-strain-rate.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High-Velocity Impact and Material Behavior · Metal and Thin Film Mechanics · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Materials Science & Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran
Steel Research Center, Faculty of Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran
Department of Mechanical Engineering, Faculty of Engineering, University of Bonab, Bonab, Iran
Advanced Materials for Clean Energy, Department of Mechanical Engineering, University of Saskatchewan, Saskatoon, Canada
Department of Mechanical Engineering, University of Saskatchewan, Saskatoon, Canada
References (38)
Show source-provided references
1. 10.1016/j.tafmec.2005.11.00510.1016/j.tafmec.2005.11.005 ↗
2. 10.1016/S0749-6419(00)00015-210.1016/S0749-6419(00)00015-2 ↗
3. 10.1016/j.msea.2013.04.10610.1016/j.msea.2013.04.106 ↗
4. 10.1016/j.msea.2014.11.01710.1016/j.msea.2014.11.017 ↗
5. 10.1016/S1006-706X(10)60116-110.1016/S1006-706X(10)60116-1 ↗
6. 10.1016/j.msea.2014.07.08410.1016/j.msea.2014.07.084 ↗
7. 10.1016/j.matdes.2010.01.04910.1016/j.matdes.2010.01.049 ↗
8. 10.1051/metal:200614210.1051/metal:2006142 ↗
9. 10.1016/j.acme.2012.06.01610.1016/j.acme.2012.06.016 ↗
10. 10.1016/S0921-5093(00)02019-010.1016/S0921-5093(00)02019-0 ↗
11. 10.1007/s11665-016-1923-910.1007/s11665-016-1923-9 ↗
12. 10.1016/S1359-6454(02)00526-810.1016/S1359-6454(02)00526-8 ↗
13. 10.1016/j.msea.2017.11.04510.1016/j.msea.2017.11.045 ↗
14. 10.1016/j.msea.2009.07.02610.1016/j.msea.2009.07.026 ↗
15. 10.4028/www.scientific.net/MSF.495-497.39310.4028/www.scientific.net/MSF.495-497.393 ↗
16. 10.1016/S1359-6454(01)00215-410.1016/S1359-6454(01)00215-4 ↗
17. Yang H · J Mater Sci Technol · 2008 · 24 · 819
18. 10.1007/s11661-018-4510-x10.1007/s11661-018-4510-x ↗
19. 10.1016/j.msea.2013.02.06210.1016/j.msea.2013.02.062 ↗
20. 10.1179/174328407X15432910.1179/174328407X154329 ↗
21. 10.1016/j.msea.2016.12.03710.1016/j.msea.2016.12.037 ↗
22. 10.1016/j.scriptamat.2009.09.01010.1016/j.scriptamat.2009.09.010 ↗
23. 10.1007/s11661-014-2705-310.1007/s11661-014-2705-3 ↗
24. 10.1016/j.msea.2013.09.08110.1016/j.msea.2013.09.081 ↗
25. 10.1016/j.msea.2014.05.05310.1016/j.msea.2014.05.053 ↗
26. 10.1016/j.msea.2010.12.05310.1016/j.msea.2010.12.053 ↗
27. 10.1016/j.msea.2015.09.10810.1016/j.msea.2015.09.108 ↗
28. 10.1023/A:101575771054610.1023/A:1015757710546 ↗
29. 10.1007/BF0258620710.1007/BF02586207 ↗
30. 10.1007/s11661-009-9916-z10.1007/s11661-009-9916-z ↗
31. 10.1016/j.msea.2009.04.03810.1016/j.msea.2009.04.038 ↗
32. 10.1007/s11661-005-0003-910.1007/s11661-005-0003-9 ↗
33. 10.1016/j.scriptamat.2012.04.00610.1016/j.scriptamat.2012.04.006 ↗
34. 10.1007/s11661-017-4245-010.1007/s11661-017-4245-0 ↗
35. 10.1016/j.actamat.2010.05.04910.1016/j.actamat.2010.05.049 ↗
36. Wan J · Metall Mater Trans A · 2001 · 44 · 345
37. 10.1016/j.scriptamat.2003.10.00610.1016/j.scriptamat.2003.10.006 ↗
38. 10.1016/S1359-6462(01)00996-410.1016/S1359-6462(01)00996-4 ↗