journal article·2023-12

Critical Assessment 43: Microstructural and mechanical properties of friction stir additively fabricated SiC-Reinforced AA6061 build

Smrity Choudhury, Rahul Das, Durjyodhan Sethi, Joydeep Roy, Barnik Saha Roy

Materials Science and Technology· Volume 39· Issue 18
Publisher page

Abstract

Friction stir additive manufacturing was employed to fabricate a SiC-reinforced AA6061 composite. The tool with a pin length of 4.5 mm (plunge depth of 50% into the lower layer thickness) was used for the experiment. The stir zone consisted of fine, equiaxed grains due to dynamic recrystallisation. Variations in grain size, as well as changes in precipitate distribution, size, and morphology, were detected along the build direction. Hardness and tensile strength varied across layers, with the top slice having the greatest values of 104.2 HV and 268.4 MPa, respectively. Notably, the FSAM build demonstrated improved ductility with a maximum of 58.98%, mostly ascribed to fragmentation and partial loss of grain-boundary phases, as well as strong interfaces that delayed necking.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Aluminum Alloys Composites Properties · Advanced Welding Techniques Analysis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

National Institute Technology Agartala, Tripura, India

Department of Mechanical Engineering, National Institute Technology Agartala, Tripura, India

Department of Mechanical Engineering, G.I.E.T., Baniatangi, India

References (60)

Show source-provided references
1. 10.1179/imr.1996.41.5.16910.1179/imr.1996.41.5.169 ↗
2. 10.1016/S1359-6462(02)00602-410.1016/S1359-6462(02)00602-4 ↗
3. 10.1007/s11661-013-1989-z10.1007/s11661-013-1989-z ↗
4. 10.1016/j.compscitech.2006.03.01810.1016/j.compscitech.2006.03.018 ↗
5. 10.1504/IJASMM.2017.08299110.1504/IJASMM.2017.082991 ↗
6. 10.1080/10408436.2017.135814610.1080/10408436.2017.1358146 ↗
7. 10.1080/10408436.2018.149025010.1080/10408436.2018.1490250 ↗
8. 10.1016/j.jmatprotec.2022.11780910.1016/j.jmatprotec.2022.117809 ↗
9. 10.1007/s40964-021-00229-810.1007/s40964-021-00229-8 ↗
10. 10.1016/j.cirpj.2021.08.00310.1016/j.cirpj.2021.08.003 ↗
11. 10.1201/978135119087910.1201/9781351190879 ↗
12. Cederqvist L, , Reynolds A. Factors affecting the properties of friction stir welded aluminum lap joints. Weld J. 2001;80(12):281-s–287-s.
13. 10.1016/j.matdes.2010.06.04810.1016/j.matdes.2010.06.048 ↗
14. 10.1007/s10853-011-5747-610.1007/s10853-011-5747-6 ↗
15. 10.1016/j.matdes.2014.09.08210.1016/j.matdes.2014.09.082 ↗
16. 10.1007/s00170-015-7695-910.1007/s00170-015-7695-9 ↗
17. 10.1016/j.msea.2020.13903510.1016/j.msea.2020.139035 ↗
18. 10.1016/j.jmapro.2019.01.04210.1016/j.jmapro.2019.01.042 ↗
19. 10.1007/s11665-020-05394-510.1007/s11665-020-05394-5 ↗
20. 10.1016/j.jallcom.2022.16801910.1016/j.jallcom.2022.168019 ↗
21. 10.1016/j.acme.2014.05.01010.1016/j.acme.2014.05.010 ↗
22. 10.1016/j.msea.2014.12.00910.1016/j.msea.2014.12.009 ↗
23. 10.1016/j.matchemphys.2022.12721010.1016/j.matchemphys.2022.127210 ↗
24. 10.1016/j.matpr.2020.07.13710.1016/j.matpr.2020.07.137 ↗
25. 10.1016/S1359-6462(01)00994-010.1016/S1359-6462(01)00994-0 ↗
26. 10.1016/j.matpr.2018.06.41210.1016/j.matpr.2018.06.412 ↗
27. 10.1016/S1003-6326(16)64318-210.1016/S1003-6326(16)64318-2 ↗
28. Ikhsan M Syamsudin H Suada M. Stiffened panel structural optimization on wing skin of “WHALE” aircraft with local and global buckling criteria. Journal of physics: conference series. IOP Publishing; 2018.10.1088/1742-6596/1130/1/012015 ↗
29. 10.1016/j.mtcomm.2020.10096410.1016/j.mtcomm.2020.100964 ↗
30. 10.1016/j.matdes.2014.02.00510.1016/j.matdes.2014.02.005 ↗
31. 10.1016/j.ijlmm.2019.04.00710.1016/j.ijlmm.2019.04.007 ↗
32. 10.1016/j.msea.2012.03.09410.1016/j.msea.2012.03.094 ↗
33. 10.1016/j.msea.2007.08.01310.1016/j.msea.2007.08.013 ↗
34. 10.1016/S0921-5093(01)01358-210.1016/S0921-5093(01)01358-2 ↗
35. 10.1007/s40194-021-01217-w10.1007/s40194-021-01217-w ↗
36. 10.1016/j.matdes.2010.11.05910.1016/j.matdes.2010.11.059 ↗
37. 10.1016/j.tafmec.2019.10225610.1016/j.tafmec.2019.102256 ↗
38. 10.1016/j.jmapro.2015.06.01710.1016/j.jmapro.2015.06.017 ↗
39. 10.1016/j.matpr.2022.02.26210.1016/j.matpr.2022.02.262 ↗
40. 10.1007/s40436-019-00288-910.1007/s40436-019-00288-9 ↗
41. 10.1016/j.jmrt.2021.01.07010.1016/j.jmrt.2021.01.070 ↗
42. 10.1177/0954408922110775510.1177/09544089221107755 ↗
43. 10.1016/j.matdes.2014.05.03810.1016/j.matdes.2014.05.038 ↗
44. 10.1007/s12666-022-02672-910.1007/s12666-022-02672-9 ↗
45. 10.1016/j.actamat.2005.03.04410.1016/j.actamat.2005.03.044 ↗
46. 10.1016/j.actamat.2006.11.01910.1016/j.actamat.2006.11.019 ↗
47. 10.1016/j.actamat.2004.05.03710.1016/j.actamat.2004.05.037 ↗
48. 10.1016/S1359-6454(99)00033-610.1016/S1359-6454(99)00033-6 ↗
49. Ikeno KMS, , Sato T. HRTEM study of nano-precipitation phases in 6000 series aluminum alloys. In: Mendez-Vilas Antonio, editor. Science, Technology and Education of Microscopy: an Overview. Formatex; 2003. p. 152–162.
50. 10.1016/j.msea.2010.12.01110.1016/j.msea.2010.12.011 ↗
51. 10.1016/S1359-6462(97)00093-610.1016/S1359-6462(97)00093-6 ↗
52. 10.1007/s11661-999-0251-110.1007/s11661-999-0251-1 ↗
53. 10.1016/j.jmatprotec.2016.05.01310.1016/j.jmatprotec.2016.05.013 ↗
54. 10.1016/j.jmrt.2019.06.05510.1016/j.jmrt.2019.06.055 ↗
55. 10.1016/j.jmapro.2015.12.00810.1016/j.jmapro.2015.12.008 ↗
56. 10.1007/s11665-022-07114-710.1007/s11665-022-07114-7 ↗
57. 10.1016/j.dt.2015.01.00210.1016/j.dt.2015.01.002 ↗
58. 10.1016/0921-5093(95)09995-610.1016/0921-5093(95)09995-6 ↗
59. Dieter GE, , Bacon D. Mechanical metallurgy. 3 New York: McGraw-hill; 1976.
60. 10.1016/j.matdes.2009.03.01810.1016/j.matdes.2009.03.018 ↗