Hydrogen redistribution under stress-induced diffusion and corresponding fracture behaviour of a structural steel
Source abstract
Abstract
Hydrogen redistribution under stress-induced hydrogen diffusion and corresponding fracture behaviour of a 960 MPa grade martensitic steel were studied. Slow strain rate tensile (SSRT) tests after hydrogen pre-charging were performed and the fracture surface was observed and analysed. The strain rate ranged from 10 −6 to 10 −4 s −1 . In the pre-charged sample with a certain hydrogen content of 0.62 ppm, hydrogen distribution was homogeneous before the SSRT test. After tensile testing, brittle fracture features appeared in the centre of the fracture surface, while ductile features appeared in the surrounding area. Brittle region size increased with the strain rate slowing down in the range from 10 −4 to 5 × 10 −6 s −1 , while it stabilised at the strain rate slower than 5 × 10 −6 s −1 . Relationship between the strain rate and the brittle region size was established and discussed based on the present data of hydrogen content in the material. This paper is part of a thematic issue on Hydrogen in Metallic Alloys
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Hydrogen embrittlement and corrosion behaviors in metals · Corrosion Behavior and Inhibition · Non-Destructive Testing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Corrosion and Protection Center, Key Laboratory for Environmental Fracture (MOE), University of Science and Technology Beijing, Beijing, China
Welding & Corrosion Research Institute, Baoshan Iron & Steel Co., Ltd, Research Institute, Shanghai, China
Department of Mechanical Engineering, University of South Florida, Tampa, FL, USA
Funding
National Natural Science Foundation of China · National Basic Research Program of China
References (30)
Show source-provided references
1. 10.1007/3-540-08883-010.1007/3-540-08883-0 ↗
2. Chu WY, Qiao LJ, Li JX, Hydrogen embrittlement and stress corrosion cracking. Beijing: Science Press; 2013. p. 82–88.
3. 10.1016/j.engfailanal.2015.11.00110.1016/j.engfailanal.2015.11.001 ↗
4. 10.1016/S1350-6307(01)00009-710.1016/S1350-6307(01)00009-7 ↗
5. Elices M · Eng Fail Anal · 2002 · 69 · 137
6. 10.1016/S1359-6454(03)00081-810.1016/S1359-6454(03)00081-8 ↗
7. 10.1016/j.corsci.2007.05.02510.1016/j.corsci.2007.05.025 ↗
8. 10.1016/j.engfailanal.2012.03.00710.1016/j.engfailanal.2012.03.007 ↗
9. 10.1016/0001-6160(70)90039-810.1016/0001-6160(70)90039-8 ↗
10. 10.1016/0022-5088(76)90022-910.1016/0022-5088(76)90022-9 ↗
11. 10.1016/0036-9748(82)90377-510.1016/0036-9748(82)90377-5 ↗
12. Momotani Y, Shibata A, Terada D, Effect of strain rate on hydrogen embrittlement in low carbon martensitic steel. Proc Int Symp on New Developments in Advanced High-Strength Sheet Steels; 2013; Vail, Colorado.
13. 10.1016/j.intermet.2003.07.00810.1016/j.intermet.2003.07.008 ↗
14. 10.1016/j.actamat.2013.04.03010.1016/j.actamat.2013.04.030 ↗
15. 10.1016/j.corsci.2011.09.02210.1016/j.corsci.2011.09.022 ↗
16. 10.1016/j.corsci.2012.01.02810.1016/j.corsci.2012.01.028 ↗
17. 10.1016/j.msea.2008.02.00210.1016/j.msea.2008.02.002 ↗
18. 10.1016/j.msea.2013.07.09710.1016/j.msea.2013.07.097 ↗
19. 10.1016/j.scriptamat.2012.03.00110.1016/j.scriptamat.2012.03.001 ↗
20. 10.1016/j.matdes.2013.02.02010.1016/j.matdes.2013.02.020 ↗
21. 10.1016/j.actamat.2014.01.04810.1016/j.actamat.2014.01.048 ↗
22. 10.1016/S1359-6454(99)00392-410.1016/S1359-6454(99)00392-4 ↗
23. 10.1179/02670830422501968710.1179/026708304225019687 ↗
24. 10.1016/S0010-938X(01)00095-610.1016/S0010-938X(01)00095-6 ↗
25. 10.1016/j.commatsci.2016.11.03410.1016/j.commatsci.2016.11.034 ↗
26. 10.1016/j.scriptamat.2005.05.01410.1016/j.scriptamat.2005.05.014 ↗
27. 10.1146/annurev.ms.08.080178.00155110.1146/annurev.ms.08.080178.001551 ↗
28. 10.1016/0921-5093(94)90975-X10.1016/0921-5093(94)90975-X ↗
29. 10.1016/j.actamat.2012.06.01410.1016/j.actamat.2012.06.014 ↗
30. 10.1016/j.actamat.2012.06.04010.1016/j.actamat.2012.06.040 ↗