High speed rolling of Mg–3Al–1Zn alloy: Texture and microstructure analysis
Source abstract
Abstract
High speed rolling (HSR) of 1000 m min−1 was employed to successfully roll AZ31 alloy in one pass with 65 reduction in thickness at 300 and 450°C. The rollability, texture and microstructure after HSR, in comparison with low speed rolling (15 m min−1), improved significantly. It is suggested that the double peak and weaker basal texture obtained after HSR are attributed to the activation of compression and double twins. After annealing, the double peak basal texture is replaced by a single peak one, which may be due to preferential grain growth of basal grains.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · Aluminum Alloy Microstructure Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Materials Engineering McGill University, Montreal, Que. H3A 2B2, Canada
Division of Materials and Manufacturing Science Graduate School of Engineering, Osaka University, Osaka, Japan
Materials Technology Laboratory CANMET, Ottawa, Ont. K1A 0G1, Canada
References (24)
Show source-provided references
1. Avedesian HBM: ‘ASM specialty handbook. Magnesium and magnesium alloys’; 2000, Materials Park, OH, ASM International.
2. 10.1179/174328408X30247710.1179/174328408X302477 ↗
3. 10.1016/S1359-6454(01)00297-X10.1016/S1359-6454(01)00297-X ↗
4. 10.1016/S1359-6454(01)00020-910.1016/S1359-6454(01)00020-9 ↗
5. 10.1016/S1359-6462(97)00344-810.1016/S1359-6462(97)00344-8 ↗
6. 10.1016/j.ijplas.2004.05.01810.1016/j.ijplas.2004.05.018 ↗
7. 10.1007/s11661-003-0146-510.1007/s11661-003-0146-5 ↗
8. 10.1016/j.msea.2007.07.00310.1016/j.msea.2007.07.003 ↗
9. Kon H · Mater. Trans. · 2007 · 48 · 202310.2320/matertrans.L-MRA2007875 ↗
10. Utsunomiya H, Sakai T, Minamiguchi S, Koh H:‘High-speed heavy rolling of magnesium alloy sheets’‘Magnesum technology 2006’(, Luo A A, et al.), 201–204; 2006, Warrendale, PA, TMS.
11. 10.4028/www.scientific.net/AMR.89-91.22710.4028/www.scientific.net/AMR.89-91.227 ↗
12. 10.4028/www.scientific.net/MSF.618-619.48310.4028/www.scientific.net/MSF.618-619.483 ↗
13. 10.1016/S0921-5093(04)00942-610.1016/S0921-5093(04)00942-6 ↗
14. 10.1016/j.scriptamat.2010.09.02910.1016/j.scriptamat.2010.09.029 ↗
15. 10.1016/j.actamat.2010.08.03110.1016/j.actamat.2010.08.031 ↗
16. 10.1007/s10853-008-3021-310.1007/s10853-008-3021-3 ↗
17. 10.1016/j.msea.2007.08.01610.1016/j.msea.2007.08.016 ↗
18. Couling SL · Trans. ASM · 1959 · 51 · 94
19. 10.1007/s11661-008-9515-410.1007/s11661-008-9515-4 ↗
20. Sanjari M, Farzadfar SA, Yue S, Essadiqi E:‘Very high strain rate deformation of AZ31B Mg alloys using split Hopkinson pressure bar’‘Magnesium technology 2010’(, Agnew S, et al.), 481–486; 2010, Warrendale, PA, TMS.
21. 10.1016/j.msea.2009.03.01510.1016/j.msea.2009.03.015 ↗
22. 10.1179/1743284711Y.000000008010.1179/1743284711Y.0000000080 ↗
23. 10.1016/j.actamat.2010.04.01710.1016/j.actamat.2010.04.017 ↗
24. 10.1179/cmq.2009.48.4.43310.1179/cmq.2009.48.4.433 ↗