journal article·2008-12

Relationship between failure behaviour and weld fusion zone attributes of austenitic stainless steel resistance spot welds

P. Marashi, M. Pouranvari, S. M. H. Sanaee, A. Abedi, S. H. Abootalebi, M. Goodarzi

Materials Science and Technology· Volume 24· Issue 12
Publisher page

Abstract

Resistance spot welding was used to join austenitic stainless steel sheets. Mechanical properties of the spot welds were evaluated using tensile shear test. Mechanical behaviour was described by peak load, failure energy and failure mode. The relationship between weld fusion zone attributes and failure behaviour was studied. Generally, it was observed that increasing fusion zone size is accompanied by an increase in load carrying capacity and energy absorption capability. However, when expulsion occurs, despite almost constant weld fusion zone size, energy absorption capability reduces significantly due to increase in electrode indentation depth. Considering the failure location and failure mechanism in the tensile shear test, minimum required fusion zone size to ensure the pull-out failure mode was estimated using an analytical model. According to this model, in addition to sheet thickness, ratio of fusion zone hardness to failure location hardness is the key metallurgical factor governing failure mode of spot welds during the tensile shear test.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Advanced Welding Techniques Analysis · Metal Forming Simulation Techniques · Welding Techniques and Residual Stresses

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. 10.1179/174328406X7425710.1179/174328406X74257 ↗
2. 10.1179/02670830422502206110.1179/026708304225022061 ↗
3. Wung P. · Exp. Meek · 2001 · 41 · 107
4. Thou M. · Weld. J. · 2003 · 82 · 72s
5. Thou M., Zhang H., and Hu S. J.: Weld. 1, 1999, 78, 305s-313s.
6. 10.1179/174329307X16440910.1179/174329307X164409 ↗
7. Marashi P., Pouranvari M., Amirabdollahian S., Abedi A., and Goodarzi M.: Mater. Sci Eng. A, doi: 10.1016/j.msea.2007.07.007.10.1016/j.msea.2007.07.007 ↗
8. Sun X., Stephens E. V., and Khaleel M. A.: Eng. Failure Anal., 2007, doi: 10.1016/j.engfailanal.2007.01.018.10.1016/j.engfailanal.2007.01.018 ↗
9. Chao J. · Sci Technol. Weld. Join · 2003 · 8 · 133
10. ‘Recommended practices for test methods and evaluation the resistance spot welding behavior of automotive sheet steels materials’, ANSI/AWS/SAE/D 8.9-97, American Welding Society, Miami, FL, USA, 1997.
11. Lippold J. C., and Kotecki D. J. ‘Welding metallurgy and weldability of stainless steels’: 2005, New York, John Wiley & Sons.
12. David S. A., Vitek J. M., and Hebble T. L.: Weld. 1, 1987, 68, 289s-300s.
13. Volger M. · 1993
14. Gould J. E., Khurana S. P., and Li T.: Weld. 1, 2006, 86, 111s-116s.
15. 10.1016/S0168-874X(99)00053-010.1016/S0168-874X(99)00053-0 ↗
16. 10.1115/1.213775110.1115/1.2137751 ↗
17. Zuniga S., and Sheppard S. D.: in ‘Fatigue and fracture mechanics’,Vol. 27, ASTM STP 1296, (ed.Piascik R. S. et al), 469-489; 1997, Philadelphia, PA, ASTM.10.1520/STP16249S ↗
18. Available at: http://www.accuratescrew.com/info/material.htm