Influence of Ti on hot ductility of C–Mn–Al steels
Source abstract
Abstract
The hot ductility of a series of C–Mn–Al steels with nominal compositions of Fe–0·1C–1·4Mn–0·3Si–0·006N with Ti additions of 0–0·04% (all compositions and percentages given in this paper are in wt-% unless otherwise stated) has been determined over the temperature range 1100–700°C. Tensile specimens were cast in situ and cooled at 25, 100, and 200 K min -1 to the test temperature and then strained to failure at a strain rate of 2 × 10 -3 s -1 . The cooling rates were chosen so that the range for conventional continuous casting (250 mm) and thin slab casting (40–60 mm) was covered. Titanium additions were generally found to impair ductility owing to the formation of fine TiN precipitates. Increasing the cooling rate to the usual rate for thin slab casting also resulted, in general, in finer AlN precipitation and finer MnS inclusions at the boundaries, leading to worse ductility. A regression equation was obtained which showed that the best ductility was obtained when the cooling rate was slow, the particle size coarse, and the N and Al levels low, in order to limit the volume fraction of the detrimental TiN and AlN precipitation. Coarse particle distributions could be achieved by having a high Ti/N ratio. On the basis of the present results it seems unlikely that Ti additions will benefit the ductility of C–Mn–Al steels significantly at the faster cooling rate usual for thin slab casting.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Magnetic Properties and Applications · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
The Department of Mechanical Engineering and AeronauticsCity University, London, EC1V OHB, UK
References (20)
Show source-provided references
1. LINAZA M. A., , ROMERO J. L., , RODRIGUES IBABE J. M., , and URCOLA J. J.: Proc. Mech. Working Steel Process. Conf., 1995, 36, 483–494.
2. 10.1179/mst.1985.1.1.8010.1179/mst.1985.1.1.80 ↗
3. TURKDOGAN E. T.: AIME Steelmaking Conf. Proc., 1987, 70, 399.
4. HATER M., , KLAGES R., , REDENZ B., , and TAFFNER K.: Open Hearth Proc. AIME, 1973, 56, 202–217.
5. PATRICK B., and LUDLOW V.: Rev. Métall., Cah. Inf. Tech., 1994, 1081-1089.
6. WOOLLEN G.: personal communication British Steel Scunth-orpe Works 1994.
7. WILLIAMS J. G.: in ‘HSLA steels technology and applications’ 261; 1984 Philadelphia PA ASM.
8. 10.1179/mst.1991.7.7.61310.1179/mst.1991.7.7.613 ↗
9. MINTZ B. ABUSHOSHA R. AYYAD S. and CARDOSO G. I. S. L.: in Proc. HSLA Steel Conf. (HSLA ‘95) Beijing China October 1995 China Science and Technology Press 342–345.
10. MINTZ B. and ABUSHOSHA R.: in ‘Hot workability of steels and light alloys - composites’ (ed. McQueen H. J. et al) 399-410; 1996 Montreal PQ The Canadian Institute of Mining Metallurgy and Petroleum.
11. MINTZ B. and CROWTHER D. N.: in Proc. Conf. on ‘Titanium technology in microalloyed steels’ (ed. Baker T. N.) Sheffield UK December 1994 98-114; 1997 London The Institute of Materials.
12. 10.1179/mst.1998.14.3.22710.1179/mst.1998.14.3.227 ↗
13. 10.1179/mst.1998.14.4.34610.1179/mst.1998.14.4.346 ↗
14. CARDOSO G. I. S. L., , MINTZ B., , and YUE S.: Ironmaking Steelmaking, 1995, 22, 365.
15. MINTZ B. YUE S. and JONAS J. J.: Int. Mater. Rev. 1991 3610.1179/imr.1991.36.1.187 ↗
16. MINTZ B.: ‘Thin slab casting’ ECSC final report on megaproject P3454Vol. 1 contract no. 7210-CA/176 City University London 1998.
17. 10.1179/03071697980327647110.1179/030716979803276471 ↗
18. 10.1007/BF0265456410.1007/BF02654564 ↗
19. MINTZ B.: unpublished work 1998.
20. 10.1179/mst.1991.7.12.110110.1179/mst.1991.7.12.1101 ↗