Influence of quenching and aging on residual stress in Al–Zn–Mg–Cu alloy 7449
Source abstract
Abstract
The present investigation aims to quantify the size and distribution of residual stresses remaining in rectilinear aluminium forged alloy blocks after they had been partially and fully heat treated. Various quench conditions were used, including water at different temperatures and polyoxyethylene glycol in two concentrations. The influence of standard and novel aging procedures, including retrogression and reaging, has been determined. Residual stresses were characterised using X-ray and neutron diffraction. Residual stress magnitudes were found to vary significantly with rapidity of cooling from the solution treatment temperature, with the subsequent aging treatments having a much smaller effect. The influence of heat treatments on the mechanical properties of the alloy was predicted by means of quench factor analysis and measured using indentation hardness and tensile testing. Quench factor analysis is also used to predict the change in lattice parameter arising from different quench paths in the strain free reference samples d0.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Aluminum Alloy Microstructure Properties · Microstructure and mechanical properties · Aluminum Alloys Composites Properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Materials Surface Science Institute University of Limerick, Limerick, Ireland
Materials Science and Simulations Paul Scherrer Institut, Villigen CH- 5232, Switzerland
Institut Laue Langevin 6 rue Jules Horowitz, Grenoble, France
References (37)
Show source-provided references
1. Kleint RE · Light Met. Age · 1958 · 2 · 14
2. 10.1115/1.282335210.1115/1.2823352 ↗
3. 10.1179/mst.1985.1.10.76510.1179/mst.1985.1.10.765 ↗
4. 10.1243/030932498151314710.1243/0309324981513147 ↗
5. Walker DM · Adv. Mater. Processes · 2002 · 160 · 57
6. Orner GM, Kulin SA: ‘Development of stress relief treatments for high strength aluminum alloys’; 1965, Cambridge, MA, Manlabs Inc.
7. 10.1520/STP26357S10.1520/STP26357S ↗
8. 10.1520/STP26356S10.1520/STP26356S ↗
9. 10.1016/j.jmatprotec.2006.02.00710.1016/j.jmatprotec.2006.02.007 ↗
10. Tanner DA, Robinson JS, Cudd RL: ‘Relief of residual stresses in aluminium alloy 7010’, Proc. 6th Int. Conf. on ‘Residual stresses’, Oxford, UK, July2000, Institute of Materials, 1299–1306.10.4028/www.scientific.net/MSF.347-349.235 ↗
11. DavisJR, Davidnson GM, LampmanSR: ‘Heat treating of aluminum’, 841–879; 1995, Materials Park, OH, ASM International.
12. 10.1007/BF0058248810.1007/BF00582488 ↗
13. 10.1179/mst.1987.3.11.92310.1179/mst.1987.3.11.923 ↗
14. Fitzpatrick ME, Fry AT, Holdway P, Kandil FA, Shackleton J, Suominen L: ‘Determination of residual stresses by X-ray diffraction’, 52; 2002, London, NPL.
15. 10.1007/978-1-4613-9570-610.1007/978-1-4613-9570-6 ↗
16. Hauk VM · Adv. X-ray Anal. · 1983 · 27 · 81
17. Cullity BD, StockSR: ‘Elements of X-ray diffraction’; 2001, Upper Saddle River, NJ, Prentice Hall.
18. 10.1016/j.msea.2006.04.06910.1016/j.msea.2006.04.069 ↗
19. 10.1007/s11661-010-0424-y10.1007/s11661-010-0424-y ↗
20. ‘Polycrystalline materials – determination of residual stresses by neutron diffraction’, ISO/TTA3, International Standardisation Organisation, Geneva, Switzerland, 2001.
21. ‘Non-destructive testing. Standard test method for determining of residual stresses by neutron diffraction’, DD CEN ISO/TS 21432, British Standards Institute, London, UK, 2005.
22. 10.1016/S0924-0136(01)00802-010.1016/S0924-0136(01)00802-0 ↗
23. 10.1107/S002188988100961810.1107/S0021889881009618 ↗
24. Hutchings MT, Withers PJ, Holden TM, Lorentzen T: ‘Introduction to the characterisation of residual stress by neutron diffraction’, 424; 2005, Boca Raton, FL, CRC Press.10.1201/9780203402818 ↗
25. 10.1016/j.actamat.2007.01.02410.1016/j.actamat.2007.01.024 ↗
26. Robinson JS · Adv. X-ray Anal. · 2009 · 52 · 667
27. 10.1016/j.jmatprotec.2009.05.01510.1016/j.jmatprotec.2009.05.015 ↗
28. 10.1007/BF0264292410.1007/BF02642924 ↗
29. Staley JT, Tiryakioglu M: ‘The use of TTP curves and quench factor analysis for property prediction in aluminum alloys’, Proc. Mater. Solutions Conf., Indianapolis, IN, USA, November2001, ASM International, 6–15.
30. Flynn RJ, Robinson JS: ‘The application of advances in quench factor analysis property prediction to the heat treatment of 7010 aluminium alloy’, Proc. Int. Conf. on ‘Advances in materials and processing technologies’, Dublin, Ireland, July2003, Dublin City University, 123–126.10.1016/j.jmatprotec.2004.04.133 ↗
31. Totten G E, Mackenzie D S, ed (eds.): ‘Handbook of aluminum’, Vol. 1, ‘Physical metallurgy and processes’, 2003, New York/Basel, Marcel Dekker Inc.
32. Croucher T: ‘Effectively quenching thick sections of high strength aluminum alloys using polyalkylene glycol quenchants’, 2009. [accessed May 1 2011] http://www.croucher.us/articles/thick-sections.
33. Trujillo DM: ‘INTEMP. Inverse heat transfer analysis’, Trucomp, Fountain Valley, CA, USA, 2003.
34. 10.1002/nme.162021021110.1002/nme.1620210211 ↗
35. 10.1007/978-1-4615-9600-410.1007/978-1-4615-9600-4 ↗
36. 10.1016/j.jmatprotec.2007.10.07210.1016/j.jmatprotec.2007.10.072 ↗
37. Nicol JA · Adv. Mater. Processes · 1996 · 149 · S40