Small punch creep testing: Review on modelling and data interpretation
Source abstract
Abstract
In many situations where the characterisation of the mechanical behaviour of a specific material is required, source material for manufacture of conventional test specimens may be at a premium. Examples include the validation of new alloys for use in the power industry, the description of the heat affected zone (HAZ) of weldments 1 or performing a remnant life study on an in service component (such as steam pipe work used extensively in the power generation industry). The potential for a limit in sample material has necessitated the development of small specimen designs and associated test methods, particularly for the determination of the creep behaviour of a sample material. The small punch creep test (SPCT) has the potential to characterise the full uniaxial creep curve (as the specimen is taken to fracture). It is for this reason that the small punch creep test has attracted much interest from the research community. Owing to the complex deformation mechanism interactions experienced in the small punch creep test, interpretation of the results has received attention from many authors since its application was proposed by Parker et al. in the 1990s 2 (based on small punch plasticity test by Manahan et al. in the 1980s 3 – 5 ). In this review paper, several methods for the interpretation of small punch creep test (SPCT) data are reported and compared, together with examples of their application. Considerations for finite element (FE) modelling of small punch creep tests are highlighted and critiqued. Recommendations for potential areas of future research are also presented based on the authors’ investigation into published literature and research.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: High Temperature Alloys and Creep · Fire effects on concrete materials · Structural Load-Bearing Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Mechanical Materials and Manufacturing Engineering, University of Nottingham, NG92RD, Nottingham, UK
Electric Power Research Institute Charlotte, NC 28262, USA
References (69)
Show source-provided references
1. Kobayashi KI, Tabuchi M, Stratford GC: ‘Creep rupture life of welding components in P92 ferritic steel using small punch creep test’, Proc. 1st Annual Int. Conf. SSTT (Small Sample Test Techniques), Vol. 63, 54–58; 2010, Metallurgical Journal.
2. Parker JD · Creep and fracture of engineering materials and structures · 1993 · 651
3. 10.13182/NT83-A3328910.13182/NT83-A33289 ↗
4. Manahan MP · Trans. Am. Nucl. Soc. · 1982 · 43 · 352
5. 10.1520/STP32993S10.1520/STP32993S ↗
6. 10.1520/STP32994S10.1520/STP32994S ↗
7. Manahan MP · J. Nucl. Mater. · 1982 · 103 · 1545
8. 10.1179/174328007X16031710.1179/174328007X160317 ↗
9. Balak M, Brezina M, Rapantova Z: ‘Mass production of SPT specimens’, Proc. 1st Annual Int. Conf. SSTT (Small Sample Test Techniques), vol. 63, 87–89; 2010, Metallurgical Journal.
10. 10.1016/0020-7403(95)00112-310.1016/0020-7403(95)00112-3 ↗
11. 10.1243/03093247JSA50210.1243/03093247JSA502 ↗
12. 10.1016/j.msea.2008.04.08710.1016/j.msea.2008.04.087 ↗
13. for Standarisation EC, Workshop Agreement: Small Punch Test Method for Metallic Materials. CEN, 2006.
14. 10.1016/j.ijpvp.2006.07.00910.1016/j.ijpvp.2006.07.009 ↗
15. 10.1115/PVP2011-5773610.1115/PVP2011-57736 ↗
16. 10.1016/j.msea.2010.01.01010.1016/j.msea.2010.01.010 ↗
17. Nishioka T, Ohsawa T, Sawaragi Y, Uemura H: ‘Effects of various factors on creep behaviour in low alloy steel by small punch testing methods’, Proc. 1st Annual Int. Conf. SSTT (Small Sample Test Techniques), Vol. 63, 34–38; 2010, Metallurgical Journal.
18. 10.1016/j.msea.2008.04.13210.1016/j.msea.2008.04.132 ↗
19. 10.1016/j.ijpvp.2006.11.00310.1016/j.ijpvp.2006.11.003 ↗
20. 10.1016/j.scriptamat.2010.11.00710.1016/j.scriptamat.2010.11.007 ↗
21. Hurst R, Bicego V, Foulds J: ‘Small punch testing for creep - Progress in Europe’, Proc. Asme Pressure Vessels and Piping Conf. 2007, 9, (2008), 433–438.10.1115/CREEP2007-26693 ↗
22. 10.1016/S0921-5093(01)01975-X10.1016/S0921-5093(01)01975-X ↗
23. 10.1016/j.ijpvp.2009.04.00510.1016/j.ijpvp.2009.04.005 ↗
24. Ule B · Mater. Tehnol. · 2004 · 17
25. 10.1179/02670830322500946310.1179/026708303225009463 ↗
26. Strum R, Grun J: ‘Accelerated test determination of creep properties for different P24 steel weldments’, Proc. 1st Annual Int. Conf. SSTT (Small Sample Test Techniques), Vol. 63, 44–49; 2010, Metallurgical Journal.
27. 10.1179/174328406X11825810.1179/174328406X118258 ↗
28. 10.1243/03093247JSA59210.1243/03093247JSA592 ↗
29. 10.1299/jmmp.4.7510.1299/jmmp.4.75 ↗
30. 10.1016/S0308-0161(03)00069-310.1016/S0308-0161(03)00069-3 ↗
31. Betten J: ‘Creep mechanics’, 3rd edn; 2008, Berlin, Springer.
32. 10.1520/JTE11549J10.1520/JTE11549J ↗
33. 10.1016/0020-7403(70)90085-810.1016/0020-7403(70)90085-8 ↗
34. 10.1016/j.jnucmat.2010.09.01510.1016/j.jnucmat.2010.09.015 ↗
35. Li YZ, Sturm R: ‘Small punch test for weld heat affected zones’, Mater. High Temp. 2006, 23, (3-4), 225–232.10.1179/mht.2006.019 ↗
36. Li YZ, Sturm R: ‘Determination of creep properties from small punch test’, Proc.e Asme Pressure Vessels Pip. Conf., Vol 3, 741–752; 2009.10.1115/PVP2008-61437 ↗
37. Strum R · Mater. Tehnol. · 2006 · 40 · 49
38. 10.1007/978-94-011-0561-310.1007/978-94-011-0561-3 ↗
39. 10.1016/0020-7403(68)90007-610.1016/0020-7403(68)90007-6 ↗
40. Dymacek P · Adv. Fract. Damage Mech. Viii · 2010 · 417 · 561
41. 10.1111/j.1460-2695.2009.01394.x10.1111/j.1460-2695.2009.01394.x ↗
42. Liu Y · Eur. J. Mech. A: Solids · 1994 · 13 · 395
43. 10.1016/S0045-7825(99)00209-110.1016/S0045-7825(99)00209-1 ↗
44. 10.1016/j.msea.2008.06.05310.1016/j.msea.2008.06.053 ↗
45. 10.1179/174328407X17970010.1179/174328407X179700 ↗
46. 10.1007/s10853-007-2388-x10.1007/s10853-007-2388-x ↗
47. 10.1007/s11223-008-0007-y10.1007/s11223-008-0007-y ↗
48. 10.1007/s12206-010-0327-210.1007/s12206-010-0327-2 ↗
49. Zhai PC, Chen G, Hashida T, Zhang QJ: ‘Evaluation on small punch creep test by finite element method’, in ‘Advances in fracture and strength’, Pts 1- 4, 2005, 297-300, 377–383.10.4028/www.scientific.net/KEM.297-300.377 ↗
50. Zhuang FK, Zhou GY, Tu ST: ‘Numerical investigation into friction effect on measuring accuracy of different small specimen creep tests’, Proc. 13th Int. Conf. on ‘Pressure vessel technology’, 2012.
51. Wang JP · Multiscale Multifunct. Funct. Graded Mater. · 2010 · 631 · 393
52. 10.1016/S0029-5493(97)00361-010.1016/S0029-5493(97)00361-0 ↗
53. Tettamanti S, Crudeli R: ‘A procedure for high temperature plant components life evaluation: Small punch creep test methodology’, ‘Case histories on integrity and failures in industry’, 1999, 895–905.
54. Hurst R, Stratford GC, Bicego V: ‘Standardisation - a route to enhancing the acceptability of small punch creep test’, Proc. ECCC Creep Conf. 2005, 349–358.
55. Hyde TH, Cortellino F, Rouse JP, Sun W: Small punch creep testing and data analysis of a P91 steel at 650°C’, in: 2nd International Conference SSTT - Determination of Mechanical Properties of Materials by Small Punch and Other Miniature Testing Techniques, (ed. , Matocha K, ed), 2012, 64–74.
56. 10.1016/j.commatsci.2006.10.02110.1016/j.commatsci.2006.10.021 ↗
57. Pan W, Boyle J, Ramlan M, Dun C, Ismail M, Hakoda K: ‘Material plastic properties characterization using a genetic algorithm and finite element method modelling of the plane strain small punch test’, Proc. 1st Annual Int. Conf. SSTT (Small Sample Test Techniques), vol. 63, 174–179; 2010, Metallurgical Journal.
58. Penuelas I, Betegon C, Rodriguez C, Belzunce J: in ‘Inverse methods on small punch tests’, (ed. , Angermann L, ed), InTech; 2011, 311–330.10.5772/12878 ↗
59. 10.1111/j.1460-2695.2009.01387.x10.1111/j.1460-2695.2009.01387.x ↗
60. 10.1243/03093247JSA22010.1243/03093247JSA220 ↗
61. 10.1016/j.commatsci.2004.01.03910.1016/j.commatsci.2004.01.039 ↗
62. 10.1016/j.engfracmech.2007.03.04710.1016/j.engfracmech.2007.03.047 ↗
63. Abendroth M: ‘Identification of creep properties for P91 steels at high temperatures using the small punch test’, Proc. 1st Annual Int. Conf. SSTT (Small Sample Test Techniques), vol. 63, Metallurgical Journal; 2010, 39–43.
64. 10.1016/j.engfracmech.2005.10.00710.1016/j.engfracmech.2005.10.007 ↗
65. 10.1016/j.commatsci.2003.08.03110.1016/j.commatsci.2003.08.031 ↗
66. 10.1016/S0143-974X(02)00018-410.1016/S0143-974X(02)00018-4 ↗
67. 10.1016/j.msea.2008.04.10810.1016/j.msea.2008.04.108 ↗
68. 10.1016/j.ijpvp.2010.07.01010.1016/j.ijpvp.2010.07.010 ↗
69. 10.1016/0956-716X(93)90411-K10.1016/0956-716X(93)90411-K ↗