Vanadic and chloride attack of superalloys
Source abstract
Abstract
The high-temperature corrosion of superalloys is associated with contaminants. When comparing contaminant conditions the contaminant flux rate (CFR) should be considered rather than the contaminant level in the fuel or environment. At temperatures above 700° C, vanadates cause fluxing of the protective oxide scales and it is shown that corrosion is determined by the CFR and temperature rather than by material selection. The effects of sulphur level in the fuel on the efficiency of magnesium additives are also considered. Chloride contamination is shown to produce scale rupture and the influence of chloride contamination under gaseous and deposit conditions is examined. In particular the differences between marine gas turbine conditions and laboratory tests to simulate hot corrosion are evaluated. It is suggested that in marine turbines fluxing mechanisms are more appropriate to the alloy than to the protective scale. Finally, the influence of chlorides on low-temperature type II hot corrosion is considered. MST/445
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · High Temperature Alloys and Creep · Corrosion Behavior and Inhibition
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. G. H. Meier and F. s. Pettit: Paper presented at Conf. on ‘High-temperature corrosion of superalloys’, London, Feb. 1986, The Institute of Metals.
2. A. J. B. Cutler: Mater. Sci. Technol. , this issue, 512–518.
3. P. Hancock: Proc. 4th US/UK Navy Conf. on ‘Gas turbine materials in a marine environment’, Annapolis, Md, June 1979, 465–473.
4. P. Hancock: ‘Corrosion of alloys at high temperature in atmospheres consisting of fuel combustion products and associated impurities’; 1968, London, HMSO.
5. M. Islam: Unpublished work, Cranfield Institute of Technology, Cranfield, Beds.
6. E. I. Speranskaya, cited by T. N. Rhys-Jones: in PhD thesis, Cranfield Institute of Technology, Beds., 1981.
7. R. C. Hurst, J. B. Johnson, M. Davies, and P. Hancock: in ‘Deposition and corrosion in gas turbines’, (ed. A. B. Hart and A. J. B. Cutler), 143–157; 1972, London, Applied Science.
8. J. G. Smeggil and N. S. Bornstein: Conf. on ‘High-temperature corrosion’, San Diego, Cal., March 1981, National Association of Corrosion Engineers, 310–315.
9. P. Hancock: in Proc. 2nd US/UK Navy Conf. on ‘Gas turbine materials in a marine environment’, Castine, Maine, July 1974; 225–236.
10. J. R. Nicholls and D. J. Stephenson: Paper presented at Conf. on ‘High-temperature corrosion of superalloys’, London, Feb. 1986, The Institute of Metals.
11. w. L. Fielder, C. A. Stearns and F. J. Kohl: NASA Tech. Mem. No. 83423, Washington, D.C., Aug. 1983.
12. c. G. McCREATH: in Proc. 3rd US/UK Navy Conf. on ‘Gas turbine materials in a marine environment’, Bath, 1976.
13. G. J. Santoro, S. A. Gokoglu, F. J. Kohl, C. A. Stearns, D. A. Rosner: ‘Deposition of Na2S04 from salt-seeded combustion gases of a high-velocity burner rig’, NASA Tech. Rept. No. 83751; 1984.
14. C. Sykes and H. T. Shirley: in Proc. Symp. on ‘Hightemperature steels and alloys for gas turbines’, Special Report No. 43, Iron and Steel Institute, London, 1951, pp. 153–169.
15. R. A. Rapp: in Proc. 4th US/UK Navy Conf. on ‘Gas turbine materials in a marine environment’, Annapolis, Md, 1979, 625–634.
16. D. A. Shores: in Proc. Conf. on ‘High-temperature corrosion’, San Diego, Cal., March 1981, National Association of Corrosion Engineers, 493–501.
17. R. L. Jones: in Proc. Conf. on ‘High-temperature corrosion’, San Diego, Cal, March 1981, National Association of Corrosion Engineers, 513–518.
18. K. T. Chiang, F. S. Pettit, and G. H. Meier: in Proc. Conf. on ‘High-temperature corrosion’, San Diego, Cal., March 1981, National Association of Corrosion Engineers, 519–530.