journal article·2007-03

Studies on photocatalytic degradation of polystyrene

A. Bandyopadhyay, G. Chandra Basak

Materials Science and Technology· Volume 23· Issue 3
Publisher page

Abstract

This paper reports the photo degradation of polystyrene (PS) by using zinc oxide (ZnO) as photo catalyst. Virgin PS is not responsive to degradation by ultra violet (UV) light because of the presence of phenyl rings in its repeating units. ZnO acts as an UV absorber and helps in transferring the absorbed energy to various bonds of PS and causes degradation. The concentration of ZnO followed by the dispersion within the PS matrix has been found to be the key as the maximum weight loss of ∼ 16% in 2 h has been obtained with 0·5 wt-% of ZnO. Below and above this concentration, the degradation is clearly low. Addition of a UV sensitive dye has further improved this degradation (up to 18%) owing to synergism with ZnO. The degradation of PS has been further highlighted from infrared spectroscopy, surface analysis, viscosity average molecular weight studies and mechanical properties analysis. A suitable mechanism supporting the UV degradation has also been proposed.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Microplastics and Plastic Pollution · Polymer Nanocomposite Synthesis and Irradiation · Polymer Nanocomposites and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (21)

Show source-provided references
1. Hudson R. ‘Commodity plastics-as engineering materials’, 1995, Shrewsbury, Rapra Technology.
2. Thomas J. ‘Polymers of tomorrow: advanced catalytic and improve process technique’: 2005, Reisinger.
3. Westling A. R. · Biomacromolecules · 2001 · 34 · 767
4. Billmeyer F. W. ‘Text book of polymer science’, 3rd edn; 1984, New York, John Wiley and Sons.
5. Vert M. ‘Biodegradable polymers and plastics’: 1992, Cambridge, Royal Society of Chemistry.10.1016/0306-3747(92)90269-6 ↗
6. 10.1002/(SICI)1097-0126(199905)48:5<346::AID-PI156>3.0.CO;2-N10.1002/(SICI)1097-0126(199905)48:5<346::AID-PI156>3.0.CO;2-N ↗
7. 10.1128/AEM.64.5.1731-1735.199810.1128/AEM.64.5.1731-1735.1998 ↗
8. 10.1002/(SICI)1099-1581(199910)10:10<625::AID-PAT930>3.0.CO;2-X10.1002/(SICI)1099-1581(199910)10:10<625::AID-PAT930>3.0.CO;2-X ↗
9. 10.1016/S0141-3910(99)00033-610.1016/S0141-3910(99)00033-6 ↗
10. 10.1016/0144-2880(84)90040-X10.1016/0144-2880(84)90040-X ↗
11. Gugumus F., Gatcher R., and Mutller H. ‘Plastic additives handbook’, 1–104; 1990, Munich, Vienna, New York, Hanser.
12. 10.1016/S0141-3910(00)00081-110.1016/S0141-3910(00)00081-1 ↗
13. 10.1002/(SICI)1097-4660(199904)74:4<349::AID-JCTB5>3.0.CO;2-710.1002/(SICI)1097-4660(199904)74:4<349::AID-JCTB5>3.0.CO;2-7 ↗
14. Neppolion B. · Ind. J. Chem. Technol · 2001 · 8 · 36
15. Pandurangan A. · Ind. J. Chem. Technol · 2001 · 8 · 496
16. Davis A. P., and Huang C. P.: Water Res. 1990, 24, 543.10.1016/0043-1354(90)90185-9 ↗
17. 10.1016/0141-3910(95)00053-O10.1016/0141-3910(95)00053-O ↗
18. 10.1016/j.polymdegradstab.2004.12.00610.1016/j.polymdegradstab.2004.12.006 ↗
19. 10.1016/S0141-3910(98)00213-410.1016/S0141-3910(98)00213-4 ↗
20. Blow C. M. ‘Rubber technology and manufacture’, 2nd edn, 244; 1982, London, Butterworths.
21. 10.1016/S0300-9440(03)00004-310.1016/S0300-9440(03)00004-3 ↗