Comparison of 3DSIM thermal modelling of selective laser melting using new dynamic meshing method to ANSYS
Source abstract
Abstract
Selective laser melting (SLM) is an additive manufacturing (AM) process in which parts are fabricated by selectively melting regions of the surface of a metallic powder bed in a layer-by-layer fashion. Various thermal phenomena such as heat conduction, convection, radiation, melting and solidification, dynamic phase changes, and evaporation occur during the SLM process. In addition, laser intensity and powder bed scan speeds during processing complicate understanding of the process due to complex dynamic interactions between the powder bed and laser. In order to study these dynamic interactions, a finite element model has been developed which uses a dynamic mesh with spatial non-linear thermal properties to track the point of laser exposure on the powder bed to study thermal evolution during SLM. The model is able to achieve a refined, localised mesh in the melt zone and heat affected zone (HAZ), surrounded by a relatively coarse mesh outside of the HAZ regions. The dynamic meshing for this implementation is achieved using both the sub-modelling functionality in ANSYS and a new set of algorithms being commercialised by 3DSIM, LLC. It was found that dynamic meshing reduces the model size and computational burden. In this paper, the use of the sub-modelling approach for dynamic meshing was verified by comparing it against a uniform fine mesh model. The results of the two models match within an acceptable tolerance. Also, a mesh sensitivity analysis was carried out in order to show solution convergence as a function of increasing mesh density. The results of this analysis were also validated using experiments to show a match between experimental and simulated melt pools. Finally, the ANSYS solution was compared with a new set of dynamic meshing finite element analysis algorithms running in Matlab. It was found that these new algorithms were significantly faster than their ANSYS counterparts for solving problems using a dynamic mesh.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · Additive Manufacturing Materials and Processes · Manufacturing Process and Optimization
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Department of Industrial Engineering University of Louisville, Louisville, KY, USA
References (33)
Show source-provided references
1. 10.1007/978-1-4419-1120-910.1007/978-1-4419-1120-9 ↗
2. Scott JA · Sci. Technol. Policy Inst. · 2012 · 1
3. 10.1016/j.jmatprotec.2003.11.05110.1016/j.jmatprotec.2003.11.051 ↗
4. 10.1108/1355254051057336510.1108/13552540510573365 ↗
5. Taylor CM: ‘Direct laser sintering of stainless steel: thermal experiments and numerical modelling’, PhD thesis, The University of Leeds, UK, 2004.
6. Ibraheem AK, Derby B and Withers PJ: ‘Thermal and residual stress modelling of the selective laser sintering process’, Materials research society symposium proceedings, 47–52; 2003, Cambridge, Cambridge University Press.10.1557/PROC-758-LL1.8 ↗
7. 10.1016/j.ijmachtools.2003.10.01910.1016/j.ijmachtools.2003.10.019 ↗
8. 10.1007/s00170-010-2641-310.1007/s00170-010-2641-3 ↗
9. 10.1016/j.ijmachtools.2009.07.00410.1016/j.ijmachtools.2009.07.004 ↗
10. 10.1007/s00170-011-3776-610.1007/s00170-011-3776-6 ↗
11. 10.1108/1355254991025184610.1108/13552549910251846 ↗
12. 10.1016/j.actamat.2005.06.01410.1016/j.actamat.2005.06.014 ↗
13. 10.1016/j.jmatprotec.2008.02.04010.1016/j.jmatprotec.2008.02.040 ↗
14. 10.1016/j.apsusc.2007.08.07410.1016/j.apsusc.2007.08.074 ↗
15. Shellabear M and Nyrhilä O: ‘Laser assisted netshape engineering 4, Proceedings of the 4th LANE’, Erlangen, Germany, September 2004, Meisenbach Verlag, 21–24.
16. 10.1016/S0007-8506(07)60676-310.1016/S0007-8506(07)60676-3 ↗
17. Patil N, Pal D and Stucker B: ‘A new finite element solver using numerical eigen modes for fast simulation of additive manufacturing processes’, Proc. Solid Freeform Fabrication Symp., Austin, TX, USA, August 2013, University of Texas at Austin.
18. Pal D · J. Manuf. Sci. Eng. · 2014
19. Nikoukar M, Patil N, Pal D and Stucker B: ‘Methods for enhancing the speed of numerical calculations for the prediction of the mechanical behavior of parts made using additive manufacturing’, Proc. Solid Freeform Fabrication Symp., Austin, TX, USA, August 2013, University of Texas at Austin.
20. Rombouts M, Kruth J.P and Froyen L: Proc. of TMS: Fabrication, materials, processing and properties, 397–404, Vol. 1; 2009, Warrendale, PA, USA, TMS.
21. Attar E: ‘Simulation of selective electron beam melting processes’, PhD thesis, University of Erlangen-Nuremberg, Erlangen, Germany, 2011.
22. 10.1088/0965-0393/21/8/08501110.1088/0965-0393/21/8/085011 ↗
23. 10.1201/978142003562910.1201/9781420035629 ↗
24. A. M. APDL, ANSYS Release 13, Canonsburg, PA, USA, 2010.
25. 10.1533/978184569014410.1533/9781845690144 ↗
26. 10.1016/j.ijmachtools.2004.04.01910.1016/j.ijmachtools.2004.04.019 ↗
27. Zeng K, Pal D and Stucker B: ‘A review of thermal analysis methods in laser sintering and selective laser melting’, Proc. Solid Freeform Fabrication Symp., Austin, TX, USA, August 2012, University of Texas at Austin, 796.
28. 10.1016/j.actamat.2009.08.02710.1016/j.actamat.2009.08.027 ↗
29. Cook RD: ‘Concepts and applications of finite element analysis’; 2007, Hoboken, NJ, USA, Wiley.
30. 10.1007/978-1-4419-7916-210.1007/978-1-4419-7916-2 ↗
31. C. ANSYS, Release 13·0-User Manual, Canonsburg, PA, USA, 2010.
32. 10.1016/S0890-6955(01)00093-110.1016/S0890-6955(01)00093-1 ↗
33. Zeng K, Pal D, Patilal N and Stucker B: ‘A new dynamic mesh method applied to the simulation of selective laser melting’, Solid Freeform Fabrication Symp., Austin, TX, USA, August 2013, University of Texas at Austin.