Overview Inclusion assisted microstructure control in C–Mn and low alloy steel welds
Source abstract
Abstract
Inclusion assisted microstructure control has been a key technology to improve the toughness of C–Mn and low alloy steel welds over the last two to three decades. The microstructure of weld metals and heat affected zones (HAZs) is known to be refined by different inclusions, which may act as nucleation sites for intragranular acicular ferrite and/or to pin austenite grains thereby preventing grain growth. In the present paper, the nature of acicular ferrite and the kinetics of intragranular ferrite transformations in both weld metals and the HAZ of steels are rationalised along with nucleation mechanisms. Acicular ferrite development is considered in terms of competitive nucleation and growth reactions at austenite grain boundary and intragranular inclusion nucleation sites. It is shown that compared to weld metals, it is difficult to shift the balance of ferrite nucleation from the austenite grain boundaries to the intragranular regions in the HAZ of particle dispersed steels because inclusion densities are lower and the surface area available for ferrite nucleation at the austenite grain boundaries tends to be greater than that of intragranular inclusions. The most consistent explanation of high nucleation potency in weld metals is provided by lattice matching between ferrite and the inclusion surface to reduce the interfacial energy opposing nucleation. In contrast, an increase in the thermodynamic driving force for nucleation through manganese depletion of the austenite matrix local to the inclusion tends to be the dominant nucleation mechanism in HAZs. It is demonstrated that these means of nucleation are not mutually exclusive but depend on the nature of the nucleating phase and the prevailing transformation conditions. Issues for further improvement of weldment toughness are discussed. It is argued that greater numbers of fine particles of a type that preferentially nucleate acicular ferrite are required in particle dispersed steels to oppose the austenite grain boundary ferrite transformation and promote high volume fractions of acicular ferrite and thereby toughness.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Microstructure and Mechanical Properties of Steels · Hydrogen embrittlement and corrosion behaviors in metals · Magnetic Properties and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (76)
Show source-provided references
1. Cochrane R. C.: Weld World 1983 21 (1/2) 16–24.10.1016/0024-6301(83)90028-6 ↗
2. Mori N. Homma H. Wakabayashi M. and Ohkita S.: J. Jpn. Weld. Soc. 1981 786.10.2207/qjjws1943.50.786 ↗
3. Watanabe I., and Kojima T.: J. Jpn. Weld Soc., 1983, 52, 223.
4. Abson D. J., and Pargeter R. J.: Int. Met. Rev., 1986, 31, (4), 141–194.
5. Bhadeshia H. K. D. H.: ‘Bainite in steels'; 1992 London The Institute of Materials.
6. 10.1179/imtr.1986.31.1.2710.1179/imtr.1986.31.1.27 ↗
7. Abson D. J.: ‘Small particles in weld metals’; 1987 IIW Document IXJ-122-87.
8. 10.1007/BF0113332710.1007/BF01133327 ↗
9. 10.1179/mst.1997.13.3.25710.1179/mst.1997.13.3.257 ↗
10. 10.1179/13621710010153843410.1179/136217100101538434 ↗
11. Oldland P. T. Ramsey C. W. Matlock D. K. and Olsen D. L.: Weld. J. Res. Suppl. 1989 68 (4) 158s-168s.
12. Yang X. B.: ‘Microstructure and mechanical properties in high strength, low alloy, C—Mn arc welds’, PhD thesis, University of Birmingham, May 2002.
13. Shiga C.: Proc. Int. Conf. on ‘The metallurgy welding and qualification of microalloyed (HSLA) steel weldments’ November 1990 Houston Texas 327–350.
14. 10.1016/0308-0161(76)90015-610.1016/0308-0161(76)90015-6 ↗
15. Grong O. and Akselsen O. M.: Met. Constr. 1986 18 557–562.10.1007/BF03291798 ↗
16. Pisarski H. G., and Pargeter R. G.: Met. Constr., 1984, 16,412–417.
17. Yamamoto K. Matsuda S. Haze T. Chijiiwa R. and Mimura H.: ‘Residual and unspecified elements in steel’ ASTM-STP 1042 266; 1989 Philadelphia PA ASTM.10.1520/STP24586S ↗
18. Eijk C. Grong O. and Hjelen J.: ‘Solid—solid phase transforma-tions II’ (ed.Koiwa M. et al) 1573; 1999 Sendai Japan. Inst. Metals.
19. Funakoshi T. Tanaka T. Ueda S. Ishikawa M. Koshizuka N. and Kobayashi K.: Tetsu-to-Hagane 1977 63 303; Trans. ISIJ 1977 17 419–427.10.2355/isijinternational1966.17.419 ↗
20. Thewlis G.: ‘Stable sulphide particle dispersed steel’ Patent Applications WO 01/66183 and GB 2363802 March 2000 Corus UK Ltd.
21. 10.1179/02670830077300266310.1179/026708300773002663 ↗
22. 10.1016/S1359-6454(02)00560-810.1016/S1359-6454(02)00560-8 ↗
23. 10.1093/jmicro/51.6.35910.1093/jmicro/51.6.359 ↗
24. 10.2355/isijinternational.36.140610.2355/isijinternational.36.1406 ↗
25. 10.2355/isijinternational.35.70810.2355/isijinternational.35.708 ↗
26. 10.2355/isijinternational.32.16910.2355/isijinternational.32.169 ↗
27. 10.2355/isijinternational.40.81910.2355/isijinternational.40.819 ↗
28. 10.1007/BF0054036910.1007/BF00540369 ↗
29. Harrison P. L. and Farrar R. A.: Met. Constr. 1987 19 392r-399r.
30. Harrison P. L. and Farrar R. A.: Met. Constr. 1987 19 447r-450r.
31. 10.1179/02670830422501032510.1179/026708304225010325 ↗
32. Thewlis G.: Join. Mater. 1989 (1) 25–31.10.1093/combul/31.1.25 ↗
33. Thewlis G.: Join. Mater. 1989 (3) 125–129.
34. Barritte G. S. and Edmonds D. V.: Proc. Int. Conf. on ‘Advances in the physical metallurgy and applications of steel’ Liverpool (8) 126-135; 1981 London The Metals Society.
35. Keville B. R. and Cochrane R. C.: Proc. Int. Conf. on ‘Trends in steels and consumables for welding’ Paper No. 28 1978 Abington Cambridge The Welding Institute.
36. Harrison P. L.: ‘Continuons cooling tranformation kinetics and microstructure of mild and low alloy steel weld metals’ PhD thesis 1982 University of Southampton.
37. 10.1179/mst.1994.10.2.11010.1179/mst.1994.10.2.110 ↗
38. Annelli E.: ‘Heterogeneous nucleation of acicular ferrite for toughness improvement of HSLA steels’ ECSC Research Contract 7210-PR/037 (97-D3•05a b c d e).
39. Saggese M. E. Bhatti A. R. Hawkins D. N. and Whiteman J. A.: Proc. Int. Conf. on ‘Effect of residual impurity and microalloying elements on weldability and weld properties’ Paper No. 15 1983 Abington Cambridge The Welding Institute.
40. 10.1179/stw.1997.2.2.6510.1179/stw.1997.2.2.65 ↗
41. 10.2355/isijinternational.35.117010.2355/isijinternational.35.1170 ↗
42. Horii Y.: ‘Effect of chemical composition on strength and toughness of welds made by large heat input submerged arc welding’, PhD thesis, Osaka University, 1995.
43. Harrison P. L.: Weld. Inst. Bull. 1989 (1) 13–15.10.1192/pb.13.5.251 ↗
44. Harrison P. L.: Weld. Inst. Bull. 1989 (2) 65–67.10.5558/tfc65067-1 ↗
45. Thewlis G. Ball A. and Whiteman J. A.: Unpublished work.
46. Ito Y., and Nakanishi M.: Sumitomo Search, 1976, 15, 42–62.
47. Grong O.: ‘Metallurgical modelling of welding’; 1994 London The Institute of Materials.
48. Evans G. M.: Oerlikon Schweissmitt., 1991, 49, (125), 22–33.
49. 10.2207/qjjws.13.50010.2207/qjjws.13.500 ↗
50. Evans G. M.: Met. Constr. 1986 18 (9) 631R-636R10.1007/978-1-349-08750-1_3 ↗
51. 10.1007/BF0265009810.1007/BF02650098 ↗
52. 10.1002/sia.740160110510.1002/sia.7401601105 ↗
53. 10.1007/BF0071973610.1007/BF00719736 ↗
54. Gladman T.: ‘The physical metallurgy of microalloyed steels’ 1997 London Institute of Materials.
55. Ph. Maitrepierre J. Rofes-vernis and D. Thivellier: in ‘Boron in steels’ Proc. Metallurical Society of the AIME Milwaukee Wisconsin 1–18; 1979 AIME.
56. Ohno Y. Uchino K. Matsuda S. Satoh T. Okamura Y. Yamamoto K. and Ikeda K.: Nippon Steel Tech. Rep. No. 36 1988 49–59.
57. 10.2355/isijinternational.34.82910.2355/isijinternational.34.829 ↗
58. 10.2355/tetsutohagane1955.73.8_101010.2355/tetsutohagane1955.73.8_1010 ↗
59. Nishimori M., , Hayashi T., , Kawabata H., and Amano K.: Curr. Adv. Mater. Process., 1997, 10, 592.
60. Ichinose T., , Okaguchi H., and Komizo Y.: Curr. Adv. Mater. Process., 1998, 11, 531.
61. Jones S. J.: ‘Modelling inclusion potency and simultaneous transformation kinetics in steels’, PhD Thesis, University of Cambridge, September 1996.
62. 10.1179/mst.1987.3.12.105110.1179/mst.1987.3.12.1051 ↗
63. 10.1007/BF0264279910.1007/BF02642799 ↗
64. 10.1007/BF0266390310.1007/BF02663903 ↗
65. Bain E. C.: Trans. Am. Inst. Min. Eng., 1924, 70, 25–46.
66. Strangwood M. and Bhadeshia H. K. D. H.: Proc. Int. Conf. on ‘Advances in welding science and technology’ Gatlinberg TN 1986 209-213; 1986 Metals Park OH ASM Int.
67. 10.1179/mst.1989.5.1.9310.1179/mst.1989.5.1.93 ↗
68. 10.1007/BF0267028810.1007/BF02670288 ↗
69. 10.2355/isijinternational1966.16.48610.2355/isijinternational1966.16.486 ↗
70. Thewlis G.: Corus RD &T Ref. 112092 Report No STC/SMT LPC/KR/08799/2004/R.
71. Myamoto G., , Furuhara T., and Maki T.: Curr. Adv. Mater. Process., 2001, 14, 1172.
72. Homma H. Ohkita H. Matsuda S. and Yamamoto K.: Welding J. 1987 66s-301s.
73. 10.2355/isijinternational.36.8010.2355/isijinternational.36.80 ↗
74. 10.2355/isijinternational.39.118810.2355/isijinternational.39.1188 ↗
75. Takamura J. and Mizoguchi S.: Proc. 6th Iron and Steel Cong. Nagoya Japan 1990 Part 1 591-597; 1990 Tokyo ISIJ.
76. 10.2355/isijinternational1966.21.49510.2355/isijinternational1966.21.495 ↗