journal article·1989-11

Formation of acicular ferrite at oxide particles in steels

F. J. Barbaro, P. Krauklis, K. E. Easterling

Materials Science and Technology· Volume 5· Issue 11
Publisher page

Abstract

Experimental steels similar in composition to structural grades were prepared from weld metal deposits to study the formation of acicular ferrite under conditions experienced in the heat affected zone for a range of welding processes. The formation of acicular ferrite under these conditions is found to be dependent on the presence of a suitable distribution of oxide inclusions > 0·4 μm in size. The characteristics and proportion of acicular ferrite in the microstructure also depend on the prior austenite grain size and cooling rate. The relationship between these factors is presented in a simplified quantitative model, which is supported by data from limited welding trials. Metallographic observations suggest that acicular ferrite forms in two stages. The first involves the formation of relatively large primary acicular ferrite plates by multiple nucleation at intragranular inclusion sites, and the second involves the formation of many smaller acicular ferrite grains that grow sympathetically from the primary plates.MST/1027
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Microstructure and Mechanical Properties of Steels · Welding Techniques and Residual Stresses · Hydrogen embrittlement and corrosion behaviors in metals

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (20)

Show source-provided references
1. EDWARDS R. H. · Aust. Weld. J. · 1986 · 31 · 11
2. ABSON D. J. · Conf. PTOC.‘Trends in steels and consurnables for welding’, 75-101; 1978, Abington, Cambridge, The Welding Institute.
3. GLOVER A. G. · Weld. J., 1977, 56, 267s-273s.
4. HOEKSTRA S. · Met. Constr. · 1986 · 18 · 771
5. FERRANTE M. · J. Mater. Sc · 1982, 17
6. LUI S. · Weld. Res. Suppl., 1986, (6), 139s-149s.
7. BARBARO F. J. · 7th National Conf. ‘AXAA-88’, University of Western Australia, Perth, Australia, August 1988, Australian X-ray Analytical Association.
8. T. GEORGE: in Proc. Conf. on ‘Strong tough structural steels’, 123; 1967, London, The Iron and Steel Institute.
9. ABSON D. J. · Weld. Inst. Res. Bull. · 1980 · 21 · 100
10. E. E. UNDERWOOD: ‘Quantitative stereology’, 1970, Reading, MA, Addison Wesley.
11. 10.1007/BF0054036910.1007/BF00540369 ↗
12. AARONSON H. I. · Trans. AIME · 1956 · 1216
13. STRANGWOOD M. · 'Advances in welding research,
14. A. CHURCH, G. KOHLER, and J. G. WILLIAMS: in Proc. Australian Welding Institute Annual Conference, Melbourne, Oct. 1987.
15. KIESSLING R. · Non-metallic inclusions in steel', 2 edn; 1978, London, The Metals Society
16. R. D. PEHLKE et al. (ed.): ‘130F steelmaking’, Vol. 2; 1975, New York, The Iron and Steel Society of AIME.
17. 10.1179/mst.1987.3.10.83610.1179/mst.1987.3.10.836 ↗
18. 10.1007/BF0265009810.1007/BF02650098 ↗
19. D. A. PORTER and K. E. EASTERLING: ‘Phase transformations in metals and alloys’: 1981; London, Van Nostrand Reinhold.
20. K. E. EASTERLING: ‘Introduction to the physical metallurgy of welding’, 1983, London, Butterworths.