journal article·2016-09Open access

Residual stress of as-deposited and rolled wire+arc additive manufacturing Ti–6Al–4V components

F. Martina, M. J. Roy, B. A. Szost, S. Terzi, P. A. Colegrove, S. W. Williams, P. J. Withers, J. Meyer, M. Hofmann

Materials Science and Technology· Volume 32· Issue 14

Abstract

Wire + arc additive manufacturing components contain significant residual stresses, which manifest in distortion. High-pressure rolling was applied to each layer of a linear Ti–6Al–4V wire + arc additive manufacturing component in between deposition passes. In rolled specimens, out-of-plane distortion was more than halved; a change in the deposits’ geometry due to plastic deformation was observed and process repeatability was increased. The Contour method of residual stresses measurements showed that although the specimens still exhibited tensile stresses (up to 500 MPa), their magnitude was reduced by 60%, particularly at the interface between deposit and substrate. The results were validated with neutron diffraction measurements, which were in good agreement away from the baseplate. This paper is part of a Themed Issue on Measurement, modelling and mitigation of residual stress.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · Titanium Alloys Microstructure and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Welding Engineering and Laser Processing Centre, Cranfield University, Building 46, MK43 0AL, UK

School of Mechanical, Aerospace and Civil Engineering, The University of Manchester, Manchester M13 9PL, UK

European Space Agency, ESTEC, Keplerlaan 1, PO Box 299, NL-2200 AG Noordwijk, The Netherlands

European Space Agency, ESTEC, EPN campus, CS20156, F-38042 Grenoble Cedex 9, France

School of Materials, The University of Manchester, Manchester M13 9PL, UK

Airbus Groups Innovation, 20A1 Building, New Filton House, Bristol BS99 7AR, UK

FRM II TU Munich, Lichtenbergstrasse 1, D-85747 Garching, Germany

Funding

Engineering and Physical Sciences Research Council · European Commission

References (37)

Show source-provided references
1. 10.1179/1743284715Y.000000007310.1179/1743284715Y.0000000073 ↗
2. 10.1007/s11661-012-1444-610.1007/s11661-012-1444-6 ↗
3. Baufeld B. · Mater. Design · 2009 · S106
4. 10.1016/j.jmatprotec.2012.02.00210.1016/j.jmatprotec.2012.02.002 ↗
5. 10.1016/j.msea.2015.10.10110.1016/j.msea.2015.10.101 ↗
6. 10.1016/j.jmatprotec.2015.11.00610.1016/j.jmatprotec.2015.11.006 ↗
7. 10.1016/j.jmatprotec.2013.04.01210.1016/j.jmatprotec.2013.04.012 ↗
8. 10.1016/j.commatsci.2011.06.02310.1016/j.commatsci.2011.06.023 ↗
9. Withers P. J. ‘Strategies for the minimization of residual stresses in welds’, 9th Int. Conf. on ‘Trends in Weld. Res.’, Chicago, Illinois, USA, 2013, 139–147.
10. 10.1179/1362171814Y.000000021910.1179/1362171814Y.0000000219 ↗
11. 10.1179/174329307X21386410.1179/174329307X213864 ↗
12. 10.1016/j.msea.2007.12.04210.1016/j.msea.2007.12.042 ↗
13. 10.1179/136217108X38862410.1179/136217108X388624 ↗
14. Kurkin S. · Weld. Prod. · 1984 · 31 · 32
15. Wen S. W., Williams S. W., Morgan S. A., Wescott A., Poad M., and Moore G. ‘Rolling of friction stir welds for residual stress and distortion control’ in ‘9th Int. Semin. Numerical Anal. of Weldability’ (ed. H. Cerjak and N. Enzinger), 579–610; 2009, Graz-Seggau, Austria.
16. 10.1179/136217110X1278588954978710.1179/136217110X12785889549787 ↗
17. 10.1179/1362171812Y.000000002110.1179/1362171812Y.0000000021 ↗
18. Martina F., Williams S., and Colegrove P. A. ‘Improved microstructure and increased mechanical properties of additive manufacture produced Ti-6Al-4V by interpass cold rolling’, 24th Int. Solid Freeform Fabr. Symp., Austin, TX, USA, 2013, 490–496.
19. 10.1007/s11661-015-3172-110.1007/s11661-015-3172-1 ↗
20. Martina F. ‘Investigation of methods to manipulate geometry, microstructure and mechanical properties in titanium large scale Wire+Arc Additive Manufacturing’, PhD thesis, Cranfield University, UK, 2014.
21. 10.1115/1.134552610.1115/1.1345526 ↗
22. 10.4028/www.scientific.net/AMR.996.69410.4028/www.scientific.net/AMR.996.694 ↗
23. 10.1016/j.jmatprotec.2015.07.00510.1016/j.jmatprotec.2015.07.005 ↗
24. Prime M. B., and DeWald A. T. ‘Practical residual stress measurement methods’, Chap. 5, (ed. Gary S. Schajer), 109–138; 2013.10.1002/9781118402832.ch5 ↗
25. 10.1049/joe.2014.013410.1049/joe.2014.0134 ↗
26. 10.1016/j.actamat.2006.04.03410.1016/j.actamat.2006.04.034 ↗
27. 10.1007/s11340-014-9971-210.1007/s11340-014-9971-2 ↗
28. 10.1007/s11340-012-9627-z10.1007/s11340-012-9627-z ↗
29. 10.1016/j.msea.2008.12.03810.1016/j.msea.2008.12.038 ↗
30. 10.1107/S002188980703026910.1107/S0021889807030269 ↗
31. Hutchings M. · 2005
32. 10.4028/www.scientific.net/MSF.777.12410.4028/www.scientific.net/MSF.777.124 ↗
33. 10.1016/j.msea.2010.12.01010.1016/j.msea.2010.12.010 ↗
34. 10.1016/j.jmatprotec.2011.12.00610.1016/j.jmatprotec.2011.12.006 ↗
35. 10.1016/0020-7403(96)00018-510.1016/0020-7403(96)00018-5 ↗
36. 10.1016/j.matdes.2015.09.11510.1016/j.matdes.2015.09.115 ↗
37. Ding J. ‘Thermo-mechanical analysis of wire and arc additive manufacturing process’, PhD thesis, Cranfield University, UK, 2012.