Low latency, electrically conductive path for low-power electronics, obtained by laser sintering of carbon-enhanced polypropylene composites
Source abstract
Abstract
This study investigated the laser-induced fabrication of conductive pathways in a technical-grade polypropylene (PP) masterbatch containing glass fibers, hollow glass microspheres, and carbon black at 10, 20, and 0.4–0.5 wt%, respectively. Graphene nanoplatelets (GNPs) and graphene oxide (GO) nanosheets were synthesised and added to the masterbatch composition, as individual or combined fillers. GNP loadings in the resulting compounds were tuned to improve mechanical properties, but not to impart significant electrical conductivity in the resulting composite materials. The different loadings (2.5 wt% GNPs, 2.5 wt% GO or 2.5 wt% GO with 1.5 wt% GNPs, respectively) were confirmed in composition by thermogravimetric analysis (TGA). A beneficial effect of GNP and GO on the mechanical properties of the composite was confirmed using elongation and three-point flexural tests. Among the series of formulations, the PP composite loaded with 2.5 wt% GNPs exhibited the best mechanical properties and was selected for laser processing experiments. Laser scribing parameters, such as optical power (W) and scribing speed (mm/s), were found to significantly influence the morphology, composition, and electrical properties of laser-scribed paths. Lowest sheet resistance (0.3 Ohm/sq) values were achieved with high laser power and low writing speeds. Morphological, compositional, and structural analyses of the scribed paths were conducted using field-emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), and micro-Raman spectroscopy. These analyses revealed that the scribed tracks were not homogeneous in composition, containing isolated graphene sheets and an accumulation layer of carbon black (CB) covering the entire irradiated path. Interestingly, the glass fibers and hollow glass microspheres provided a good support for the accumulation of carbon black along the laser irradiated paths. More interestingly, this accumulation layer of agglomerated CB was found to provide a continuous conductive network for effective electron transport. We also explored the capabilities of these laser-scribed tracks to transmit electrical signals, assessing their performance in comparison to standard USB cables. Our findings indicate that the laser-scribed tracks achieved comparable latency and data transfer rates to traditional USB cables. Moreover, no errors were observed during data transfer, and the phase correlation necessary for serial communication was preserved. These results demonstrate that laser-scribed tracks can reliably support data transfer operations, offering a simple route of embedding components through CO2 laser irradiation processing. By laser-treating a rectangular area, we also fabricated a polymer-based electric heater with high thermal homogeneity and a linear voltage-temperature dependence.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Graphene research and applications · Carbon Nanotubes in Composites · Nanomaterials and Printing Technologies
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (75)
Show source-provided references
1. Polymers in our daily life10.15171/bi.2017.09 ↗
2. Additive processing of polymers10.1002/mame.200800121 ↗
3. Impact modification of fiber reinforced polypropylene composites with flexible poly(ethylene terephthalate) fibers10.1002/pi.6210 ↗
4. Effect of hollow glass microspheres with different contents and types on properties of polypropylene composites10.1002/slct.202202963 ↗
5. Thermal/electrical properties and texture of carbon black PC polymer composites near the electrical percolation threshold10.3390/jcs5080212 ↗
6. Thermal, morphological, electrical properties and touch-sensor application of conductive carbon black-filled polyamide composites10.3390/nano11113103 ↗
7. 30 - automotive applications of plastics: Past, present, and future
8. Composites for electric vehicles and automotive sector: a review10.1016/j.geits.2022.100043 ↗
9. State of the art in recycling waste thermoplastics and thermosets and their applications in construction10.1016/j.resconrec.2021.105776 ↗
10. Critical review on the characterization, preparation, and enhanced mechanical, thermal, and electrical properties of carbon nanotubes and their hybrid filler polymer composites for various applications
11. A review of the electrical and mechanical properties of carbon nanofiller-reinforced polymer composites10.1007/s10853-018-3006-9 ↗
12. Boosting electrical and piezoresistive properties of polymer nanocomposites via hybrid carbon fillers: a review10.1016/j.carbon.2020.11.070 ↗
13. Graphene-loaded recycled PET: exploring and enhancing electrical conductivity through processing and laser treatments near the electrical percolation threshold
14. Modeling the electrical resistivity of polymer composites with segregated structures10.1038/s41467-019-10514-4 ↗
15. Influence of different carbon-based fillers on electrical and mechanical properties of a PC/ABS blend10.3390/polym12010029 ↗
16. Conductive polymer composites with segregated structures10.1016/j.progpolymsci.2014.07.007 ↗
17. Engineering segregated structures in a cross-linked elastomeric network enabled by dynamic cross-link reshuffling10.1021/acsmacrolett.0c00852 ↗
18. An embedded non-intrusive graphene/epoxy broadband nanocomposite sensor co-cured with GFRP for in situ structural health monitoring10.1016/j.compscitech.2023.109995 ↗
19. Graphene-based transparent flexible strain gauges with tunable sensitivity and strain range10.1021/acsanm.3c03967 ↗
20. Multifunctional conductive paths obtained by laser processing of non-conductive carbon nanotube/polypropylene composites10.3390/nano11030604 ↗
21. Flash healing of laser-induced graphene10.1038/s41467-024-47341-1 ↗
22. Laser-patterned polyurethane composites with graphene, graphene oxide, and aramid fibers for the production of electric circuits, sensors, and heaters10.1021/acsanm.4c04059 ↗
23. Extensive reduction of graphene oxide on thin polymer substrates by ultrafast laser for robust flexible sensor applications10.1016/j.apsusc.2022.156067 ↗
24. Bioderived laser-induced graphene for sensors and supercapacitors10.1021/acsami.3c07687 ↗
25. Laser-induced graphene10.1021/acs.accounts.8b00084 ↗
26. A study on the effects of graphene nano-platelets (GnPs) sheet sizes from a few to hundred microns on the thermal, mechanical, and electrical properties of polypropylene (PP)/GnPs composites10.3144/expresspolymlett.2018.76 ↗
27. Metal replacement in aeronautics applications using two-dimensional multifunctional composites10.1002/adem.202401298 ↗
28. Recent progress in non-photolithographic patterning of polymer thin films10.1016/j.progpolymsci.2023.101688 ↗
29. Water-based direct photopatterning of stretchable PEDOT:PSS using amphiphilic block copolymers10.1038/s41528-024-00308-0 ↗
30. Tri-layer contact photolithography process for high-resolution lift-off10.1016/j.mee.2021.111545 ↗
31. Imprint lithography with sub-10 nm feature size and high throughput10.1016/S0167-9317(96)00097-4 ↗
32. Multilength scale patterning of functional layers by roll-to-roll ultraviolet-light-assisted nanoimprint lithography10.1021/acsnano.5b07411 ↗
33. Recent advances in laser-induced graphene: mechanism, fabrication, properties, and applications in flexible electronics
34. Laser cutting of polymeric materials: an experimental investigation10.1016/j.optlastec.2009.09.006 ↗
35. Micro-texturing of polymer surfaces using lasers: a review10.1007/s00170-022-08731-1 ↗
36. Cutting and welding using a CO2 laser10.1016/0030-3992(72)90027-8 ↗
37. Functional Piezoresistive Polymer Composites Based on CO2 Laser-Irradiated Graphene Oxide-Loaded Polyurethane: Morphology, Structure, Electrical and Piezoresistive Properties10.3390/nano13010168 ↗
38. Two-step approach based on selective laser sintering for high performance carbon black/ polyamide 12 composite with 3D segregated conductive network10.1016/j.compositesb.2019.107214 ↗
39. The second laser revolution in chemistry: emerging laser Technologies for Precise Fabrication of multifunctional nanomaterials and nanostructures10.1002/adfm.202405457 ↗
40. Laser-induced graphene formation on chitosan derivatives toward ecofriendly electronics10.1021/acsanm.3c01408 ↗
41. Effects of chemical structure and morphology of graphene-related materials (GRMs) on melt processing and properties of GRM/polyamide-6 nanocomposites10.1016/j.rinma.2020.100105 ↗
42. A new compounding method for exfoliated graphite–polypropylene nanocomposites with enhanced flexural properties and lower percolation threshold10.1016/j.compscitech.2006.11.014 ↗
43. Graphite nanoplatelets and carbon nanotubes based polyethylene composites: electrical conductivity and morphology10.1016/j.matchemphys.2013.08.008 ↗
44. LagBox - Measuring the Latency of USB-Connected Input Devices. Presented at Extended Abstracts of the 2018
45. Raman Spectrum of graphene and graphene layers10.1103/PhysRevLett.97.187401 ↗
46. Thermal decomposition products of polypropylene
47. Kinetics of the thermal and Thermo-oxidative degradation of polystyrene, polyethylene and poly(propylene)10.1002/1521-3935(20010301)202:6<775::AID-MACP775>3.0.CO;2-G ↗
48. Crystallization behaviors in the isotactic polypropylene/graphene composites10.1016/j.polymer.2014.06.027 ↗
49. Raman, IR and INS Characterization of Functionalized Carbon Materials
50. Determination of Isotacticity in polypropylene10.1002/app.1962.070062426 ↗
51. FTIR-ATR spectroscopic, thermal and microstructural studies on polypropylene-glass fiber composites10.1016/j.molstruc.2022.133181 ↗
52. A method to reveal bulk and surface crystallinity of polypropylene by FTIR spectroscopy - suitable for fibers and nonwovens10.1016/j.polymertesting.2018.08.018 ↗
53. Blaine · 2026
54. Fracture toughness of polypropylene-based particulate composites10.3390/ma2042046 ↗
55. Chapter 8: Filled thermoplastics
56. Laser-induced porous graphene films from commercial polymers10.1038/ncomms6714 ↗
57. Structure and properties of metal-free conductive tracks on polyethylene/multiwalled carbon nanotube composites as obtained by laser stimulated percolation10.1016/j.carbon.2013.04.066 ↗
58. A novel approach to obtain conductive tracks on PP/MWCNT nanocomposites by laser printing10.1039/C6RA02726A ↗
59. Scanning Electron microscopy
60. Laser ablation mechanism and performance of glass fiber-reinforced phenolic composites: an experimental study and dual-scale modelling10.1016/j.cja.2024.05.042 ↗
61. Upgrading polyolefin plastic waste into multifunctional porous graphene using silicone-assisted direct laser writing
62. Controllable black or white laser patterning of polypropylene induced by carbon nanotubes
63. Laser-carbonization – a powerful tool for Micro-fabrication of patterned electronic carbons10.1002/adma.202211054 ↗
64. Practical guide for curve fitting in x-ray photoelectron spectroscopy10.1116/6.0000377 ↗
65. Practical guide to the use of backgrounds in quantitative XPS10.1116/6.0000661 ↗
66. Carrier mobility enhancement of tensile strained Si and SiGe nanowires via surface defect engineering10.1021/acs.nanolett.5b01634 ↗
67. Crist · 1999
68. C sp2/sp3 hybridisations in carbon nanomaterials – XPS and (X)AES study10.1016/j.apsusc.2018.04.269 ↗
69. Polyethylene microtubes from silica-fiber-based polyethylene composites synthesized by using an in situ catalytic method10.1002/adma.200601251 ↗
70. Andreassen · 1999 · 966
71. Raman microspectroscopy characterization of carbon blacks: spectral analysis and structural information10.1016/j.carbon.2014.12.030 ↗
72. Raman spectroscopic characterization of some commercially available carbon black materials10.1016/0008-6223(95)00117-V ↗
73. Laser-induced carbonization strategy for designing efficient dual-layer solar wastewater evaporator10.1016/j.cej.2024.153498 ↗
74. Locally controllable surface foaming of polymers induced by graphene via near-infrared pulsed laser10.1021/acssuschemeng.9b07046 ↗
75. Laser irradiation method to prepare polyethylene porous fiber membrane with ultrahigh xylene gas filtration capacity10.1016/j.jhazmat.2020.124395 ↗