journal article·2020-02

Converse piezoelectric behavior of three-dimensionally printed polymer and comparison of the in-plane and out-of-plane behavior

Patatri Chakraborty, Chi Zhou, D.D.L. Chung

Publisher page

Abstract

Abstract The converse piezoelectric effect (out-of-plane and in-plane directions) is reported in 3D-printed polymer without filler or poling, consistent with previously reported direct piezoelectric effect (out-of-plane direction only). Resin 1 (acrylate ester, viscosity 95 cP) and Resin 2 (methacrylate, viscosity 2950 cP) are used in the printing by stereolithography. Both direct and converse effects stem from the 2D shear stress during printing causing 2D in-plane molecular alignment. Due to its higher viscosity, Resin 2 gives more molecular alignment and hence higher piezoelectric coupling coefficient d (0.4 vs. 0.2 pC/N). The out-of-plane d is similar for the direct and converse effects in the linear regime, which occurs below 30 kPa compressive stress in the direct effect and below 1 V/m in the converse effect. Both converse and direct effects are reversible, whether in the linear regime or not. The higher is the applied electric field, the lower is d, due to strain saturation.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced Sensor and Energy Harvesting Materials · Additive Manufacturing and 3D Printing Technologies · Nanofabrication and Lithography Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. H. Kim F. Torres Y. Wu D. Villagran Y. Lin T. Tseng Integrated 3D printing and corona poling process of PVDF piezoelectric films for pressure sensor application Smart Mater. Struct. 26 8 2017 085027/1 085027/9.10.1088/1361-665X/aa738e ↗
2. Self-powered pressure sensor with fully encapsulated 3D printed wavy substrate and highly-aligned piezoelectric fibers array10.1038/s41598-017-07360-z ↗
3. H. Chabok, C. Zhou, Y. Chen, A. Eskandarinazhad, Q. Zhou, K Shung, Proc ASME 2012 Int Symp Flexible Automation 2012, ISFA2012-7119.
4. 3D optical printing of piezoelectric nanoparticle-polymer composite materials10.1021/nn503268f ↗
5. 3D printing of BaTiO3/PVDF composites with electric in situ poling for pressure sensor applications10.1002/mame.201700229 ↗
6. 3D printing of piezoelectric element for energy focusing and ultrasonic sensing10.1016/j.nanoen.2016.06.048 ↗
7. Piezoelectric component fabrication using projection-based stereolithography of barium titanate ceramic suspensions10.1108/RPJ-11-2015-0162 ↗
8. One-step solvent evaporation-assisted 3D printing of piezoelectric PVDF nanocomposite structures10.1021/acsami.7b04095 ↗
9. 4D printing based piezoelectric composite for medical applications10.1002/polb.24763 ↗
10. Simultaneous 3D printing and poling of PVDF and its nanocomposites10.1021/acsaem.7b00337 ↗
11. Fabrication and characterization of 3D printed BaTiO3/PVDF nanocomposites10.1177/0021998317704709 ↗
12. Research highlights: printing the future of microfabrication10.1039/c4lc90023e ↗
13. Biobased acrylate photocurable resin formulation for stereolithography 3D printing10.1021/acsomega.7b01648 ↗
14. Stereolithography-based 3D printed photosensitive polymer/boron nitride nanoplatelets composites10.1002/pc.24662 ↗
15. Decreasing the shear-stress-induced in-plane molecular alignment by unprecedented stereolithographic delay in three-dimensional printing10.1007/s10853-018-3047-0 ↗
16. Effects of printing conditions on the molecular alignment of three-dimensionally printed polymer10.1016/j.compositesb.2017.09.067 ↗
17. First observation of the effect of the layer printing sequence on the molecular structure of three-dimensionally printed polymer, as shown by in-plane capacitance measurement10.1016/j.compositesb.2017.12.008 ↗
18. Piezoelectric behavior of three-dimensionally printed acrylate polymer without filler or poling10.1007/s10853-018-2006-0 ↗
19. Effect of stress on the capacitance and electric permittivity of three-dimensionally printed polymer, with relevance to capacitance-based stress monitoring10.1016/j.sna.2017.07.008 ↗
20. Unprecedented sensing of interlayer defects in three-dimensionally printed polymer by capacitance measurement10.1088/1361-665X/aae16e ↗
21. Enhancing the inherent piezoelectric behavior of three-dimensionally printed acrylate polymer by electrical poling10.1088/1361-665X/aae59d ↗
22. 3D printing of an interpenetrating network hydrogel material with tunable viscoelastic properties10.1016/j.jmbbm.2016.07.020 ↗
23. Frontal conversion and uniformity in 3D printing by photopolymerisation10.3390/ma9090760 ↗