journal article·2007-08

Thermal stability and electrode properties of melt-spun Mg65Cu25Nd10 amorphous alloy

L.J. Huang, G.Y. Liang, Z.B. Sun, Y.F. Zhou, D.C. Wu

Publisher page

Abstract

Abstract Amorphous Mg-based alloy Mg 65 Cu 25 Nd 10 was prepared by melt-spinning. Thermal stability and phase transition in the as-quenched alloy were studied by TEM, DSC, X-ray and electron diffraction. It was found that the crystallization process of melt-spun Mg 65 Cu 25 Nd 10 ribbons consists of three steps. The first crystallization reaction at about 180 °C is connected with the formation of Mg 2 Cu nanocrystalline phase, followed by formation of a coarser grained α-Mg crystalline phase (210–225 °C) corresponding to a second crystallization reaction. At higher temperatures a third exothermic effect (at about 320 °C) can be detected and the stable Mg 2 Cu, α-Mg and Cu 5 Nd phases are present. The electrode properties of the as-quenched and the annealed samples (partially and fully crystallized) were measured and compared as well. The amorphous Mg 65 Cu 25 Nd 10 alloy shows the highest discharge capacity (430.4 mAh/g) and the best life cycle properties in comparison with those of partially crystalline (421.8 mAh/g) and almost completely crystallized microstructural states (304.3 mAh/g). It was conformed that the discharge capacity is significantly dependent on the composition and microstructure of the electrode materials.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Hydrogen Storage and Materials · Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (17)

Show source-provided references
1. Lee · J. Alloys Compd. · 2000 · 313 · 25810.1016/S0925-8388(00)01205-6 ↗
2. Sun · Electrochem. Solid State Lett. · 2000 · 3 · 12110.1149/1.1390976 ↗
3. Abdellaoui · J. Alloys Compd. · 2003 · 356/357 · 55710.1016/S0925-8388(03)00119-1 ↗
4. Mohamad · J. Power Sources · 2003 · 115 · 16110.1016/S0378-7753(02)00619-5 ↗
5. Hong · J. Alloys Compd. · 2002 · 330–332 · 58410.1016/S0925-8388(01)01507-9 ↗
6. Spassov · J. Alloys Compd. · 1998 · 279 · 27910.1016/S0925-8388(98)00680-X ↗
7. Wang · J. Alloys Compd. · 2002 · 336 · 29710.1016/S0925-8388(01)01891-6 ↗
8. Shin-Ichi · J. Alloys Compd. · 2002 · 334 · 21910.1016/S0925-8388(01)01745-5 ↗
9. Inoue · Mater. Trans. JIM · 1992 · 33 · 93710.2320/matertrans1989.33.937 ↗
10. Wu · Int. J. Rapid Solidif. · 1993 · 8 · 65
11. Inoue · Mater. Sci. Eng. A · 1993 · 173 · 110.1016/0921-5093(93)90175-E ↗
12. Kam · J. Mater. Res. · 1999 · 14 · 163810.1557/JMR.1999.0220 ↗
13. Gebert · Mater. Sci. Eng. A · 2001 · 299 · 12510.1016/S0921-5093(00)01401-5 ↗
14. Savyak · J. Alloys Compd. · 2004 · 364 · 22910.1016/S0925-8388(03)00529-2 ↗
15. Huang · J. Alloys Compd. · 2006 · 421 · 27910.1016/j.jallcom.2005.11.039 ↗
16. Huang · J. Power Sources · 2006 · 160 · 68410.1016/j.jpowsour.2005.12.072 ↗
17. Orimo · Appl. Phys. A · 2001 · 72 · 16710.1007/s003390100771 ↗