journal article·2020-11

Chalcopyrite CuAlS2 nanocomposite thin films with unusual and promising peculiarities fabricated by two consecutive methods; powder metallurgy and thermal evaporation

Moataz H. Ata, Elsayed Abdellateef, Mahmoud Elrouby

Publisher page

Abstract

Abstract The current work is focused on fabricating bulk CuAlS2 samples by powder metallurgy technique (P/M) at a compacting pressure of 350 MPa, sintering time 2hr and different sintering temperatures (100, 150, 200, 250 and 300 °C). These bulk samples were used to prepare CuAlS2 thin films by vacuum thermal evaporation. The phases, morphology, and content of elements for the CuAlS2 thin films were characterized using X-ray diffraction, scanning electron microscopy (SEM) provided with EDS. Wear, friction, slurry erosion, and electrochemical corrosion measurements were achieved. XRD analysis of the CuAlS2 thin film revealed the formation of the CuAlS2 with the preferred orientation (0 0 8). It is observed that the wear rate decreased from 119.7 × 10−6 mm3/Nm at sintering temperature 250 °C to 58.3 × 10−6 mm3/Nm at sintering temperature 300 °C. Moreover, Mott–Schottky’s plot of the sample that sintered at 250 °C shows unusual property and transformed from n-type to p-type at the potential of ~0.1 V.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Chalcogenide Semiconductor Thin Films · High-Temperature Coating Behaviors · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (62)

Show source-provided references
1. Study of the growth of CuAlS2 thin films on oriented silicon (111)10.1016/j.tsf.2008.10.086 ↗
2. Structural, morphological and optical properties of CuAlS2 films deposited by spray pyrolysis method10.1016/j.optcom.2007.11.031 ↗
3. Structural phase transition and electrical transport properties of CuInS2 nanocrystals under high pressure10.1021/jp511684u ↗
4. Structure and optical properties of CuAlS2 thin films prepared via chemical bath deposition
5. Electrically induced optical absorption in Al-CuAlS2-Au diode10.1143/JJAP.38.L626 ↗
6. Optical properties of chemical bath deposited CuAlS2 thin films
7. Influence of substrate temperature on optical properties of nanostructured CuAlS2 thin films grown by two stage vacuum thermal evaporation technique
8. Ab initio studies of structural, electronic, optical and thermal properties of CuAlS2 chalcopyrite10.1016/j.comptc.2011.03.008 ↗
9. The effect of thickness on structural properties of CuAlS2 thin films by thermal evaporation technique
10. Heat capacity and thermodynamic functions of the CuAlS2 semiconductor in the temperature range from 80 to 300 K10.1002/pssb.200540064 ↗
11. Study on the effects of different sulfur vaporization temperature on the properties of CuInS2 thin films10.1016/j.apsusc.2013.01.087 ↗
12. Investigation of the sub-bandgap photoresponse in CuGaS2: Fe for intermediate band solar cells10.1002/pip.1197 ↗
13. B. Murali, S.B. Krupanidhi, Tailoring the Cu (In, Al) S2 nanostructures for photonic applications. In: Photovoltaic Specialists Conference (PVSC), 2013 IEEE 39th (pp.2017-2022), Bangalore, India, 2013, June.10.1109/PVSC.2013.6744868 ↗
14. Optical behavior and structural property of CuAlS2 and AgAlS2 wide-bandgap chalcopyrites10.1364/AO.53.0000E7 ↗
15. Growth and microtopographic study of CuAlS2 single crystals10.1063/1.4810486 ↗
16. Optical properties of wide-band-gap chalcopyrite CuAl (Se 0.5 S 0.5)2 evaluated by thermo-reflectance spectroscopy10.1364/OME.3.000480 ↗
17. Cu (In, Al) S2 thin film solar cell10.1143/JJAP.44.1204 ↗
18. CuAlS2 thin films–Dip coating deposition and characterization
19. Growth and optimization by post-annealing of chalcopyrite CuAlS2 compound10.1051/epjap:2006097 ↗
20. CuAlS2 thin-films prepared by sulfurization of metallic precursors and their properties10.1143/JJAP.43.6890 ↗
21. Study of the optical properties of CuAlS2 thin films prepared by two methods10.1007/s00339-017-0833-5 ↗
22. Effect of Bi incorporation and temperature on the properties of sprayed CuInS2 thin films10.1016/j.physb.2012.08.045 ↗
23. Effect of zinc doping and temperature on the properties of sprayed CuInS2 thin films10.1016/j.mssp.2012.04.001 ↗
24. CuAlS2: Mn thin film EL devices prepared by electron- beam evaporation method using phosphor pellet
25. Characterization of n and p-type (SnO2)x(ZnO)1-x nanoparticles thin films10.1051/epjap/2015150188 ↗
26. Synthesis and characterization of CuAlS2 nanoparticles by facile heat arrested method
27. Optical and electrical properties study on p-type conducting CuAlS2+x with wide band gap10.1016/j.scriptamat.2007.08.015 ↗
28. Effect of impact angle on slurry erosion behavior and mechanisms of carburized AISI 5117 steel10.1115/1.4025874 ↗
29. Effect of impingement angle on slurry erosion behaviour and mechanisms of 1017 steel and high-chromium white cast iron10.1016/j.wear.2006.11.018 ↗
30. B. Murali, S.B. Krupanidhi, Tailoring the Cu (In, Al)S2 nanostructures for photonic applications. In Photovoltaic Specialists Conference (PVSC), 2013 IEEE 39th (pp.2017-2022), Bangalore, India, 2013, June.10.1109/PVSC.2013.6744868 ↗
31. Optical properties of wide-band-gap chalcopyrite CuAl (Se0.5S0.5)2 evaluated by thermoreflectance spectroscopy10.1364/OME.3.000480 ↗
32. Biological surface science10.1016/S0039-6028(01)01809-X ↗
33. Effect of ethylene glycol monomethyl ether ratio in mixed solvent on surface morphology, wettability and photocatalytic properties of ZnO thin films10.1007/s10854-014-1965-4 ↗
34. Microstructure, wettability, optical and electrical properties of HFO2 thin films: Effect of oxygen partial pressure10.1016/j.jallcom.2015.12.080 ↗
35. Comparison of methods for measuring surface roughness of ceramic10.1111/j.1365-2842.1995.tb00795.x ↗
36. Initial contact angle measurements on variously treated dental/medical titanium materials
37. Relationship between surface properties (roughness, wettability and morphology) of titanium and dental implant removal torque10.1016/j.jmbbm.2007.12.002 ↗
38. F.M. El-Hossary, A.A. El-Rahman, M.H. Ata, M.A. Hassan, Effect of nitrogen gas ratio on the properties of TI-ZR-N coatings deposited by pulsed magnetron sputtering. JES, Assiut University, Faculty of Engineering, 45(2) 142–155, 2017.10.21608/jesaun.2017.116097 ↗
39. Effects of topography and composition of titanium surface oxides on osteoblast responses10.1016/j.biomaterials.2003.11.011 ↗
40. Microstructure and wear properties of Al-Pb-Cu alloy synthesized by mechanically alloying
41. Tribology of polymers: adhesion, friction, wear, and mass-transfer10.1016/j.triboint.2005.07.016 ↗
42. Structure, internal stresses, adhesion and wear resistance of sputtered alumina coatings10.1016/0040-6090(87)90176-3 ↗
43. Effect of surface roughness of top cover layer on the efficiency of dye-sensitized solar cell10.1016/j.solener.2012.04.007 ↗
44. Effect of impact angle on glass surfaces eroded by sand blasting10.1016/S0955-2219(99)00140-5 ↗
45. Effects of the impact angle variations on the erosion rate of glass in powder blasting process10.1007/s00170-003-1724-9 ↗
46. Effects on a sheet surface of an erosive particle jet upon impact10.1016/0043-1648(94)06562-4 ↗
47. Y.M. Abd-Elrhman, A. Abouel-Kasem, K.M. Emara, S.M. Ahmed, Effect of Impact Angle on Slurry Erosion Behavior and Mechanisms of Carburized AISI 5117 Steel, J. Tribol. 136(1) (2014) 011106 (1-9).10.1115/1.4025874 ↗
48. Effect of impact angle on the slurry erosion–corrosion of 304L stainless steel10.1016/S0043-1648(00)00344-6 ↗
49. Impact angle, particle energy and mass loss in erosion by dilute slurries10.1016/0043-1648(95)07120-2 ↗
50. H.M. Clark, Test methods and applications for slurry erosion—a review, in: Tribology: Wear Test Selection for Design and Application. ASTM International, Pennsylvania, United States, 1993.10.1520/STP15968S ↗
51. Design of a slurry erosion test rig10.1016/0043-1648(90)90093-P ↗
52. A comparison of slurry erosion characteristics of TiNi shape memory alloys and SUS304 stainless steel10.1016/S0043-1648(01)00580-4 ↗
53. Effect of impingement angle on slurry erosion behaviour and mechanisms of 1017 steel and high-chromium white cast iron10.1016/j.wear.2006.11.018 ↗
54. On the velocity dependence of the erosion of ductile metals by solid particles at low angles of incidence10.1016/0043-1648(78)90147-3 ↗
55. A model for the erosion of metals by spherical particles at normal incidence10.1016/0043-1648(81)90347-1 ↗
56. Erosion mechanism in ductile metals10.1016/0043-1648(81)90268-4 ↗
57. Low-cost and eco-friendly nebulizer spray coated CuInAlS2 counter electrode for dye-sensitized solar cells10.1016/j.physb.2018.01.042 ↗
58. Nanophase CuInS2 nanosheets/CuS composite grown by the SILAR method leads to high performance as a counter electrode in dye sensitized solar cells10.1039/C4RA01740D ↗
59. Effect of annealing atmosphere on quaternary chalcogenide-based counter electrodes in dye-sensitized solar cell performance: synthesis of Cu2FeSnS4 and Cu2CdSnS4 nanoparticles by thermal decomposition process10.1039/C6RA28889H ↗
60. Electrical, electrochemical and photo-electrochemical studies on the electrodeposited n-type semiconductor hexagonal crystalline CdS thin film on nickel substrate10.1007/s10854-014-2351-y ↗
61. The influence of passivation on the kinetics of the dissolution of iron—I. Outer layer of the passivating film as a heavy doped thin semiconductor and mott-schottky equation10.1016/0013-4686(89)87073-2 ↗
62. Electrocatalysis in water electrolysis with solid polymer electrolyte10.1016/j.electacta.2003.04.001 ↗