journal article·2017-12

Effect of starch addition on structural, electrical and thermal properties of delafossite CuAl 0.9 Fe 0.1 O 2

Sarayut Pantian, Rachsak Sakdanuphab, Aparporn Sakulkalavek

Publisher page

Abstract

Abstract In this study, starch was added to the delafossite CuAl0.9Fe0.1O2 with the purpose of creating porosity in the structure. Increasing porosity contributes to a decrease in thermal conductivity, which increases the figure of merit (ZT) for thermoelectric properties. The results show that the porosity of the material increased as starch content was raised from 0 to 3 wt%. The thermal conductivity of CuAl0.9Fe0.1O2 at room temperature decreased from 9.12 to 5.44 W/m.K as porosity increased from 12.0 to 43.4 vol%. The electrical conductivity decreased with increasing starch concentration, with the values ranging from 0.32 to 0.08 S/cm. Of all samples from 0 to 3 wt% starch, the sample with 1 wt% showed the highest ZT value. The increase of the ZT value resulted in a decrease in thermal conductivity due to sample porosity.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Copper-based nanomaterials and applications · ZnO doping and properties · Electronic and Structural Properties of Oxides

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. Bipolar doping and band-gap anomalies in delafossite transparent conductive oxides10.1103/PhysRevLett.88.066405 ↗
2. Electronic structure and bonding in CuMO2 (M=Al, Ga, Y) delafossite-type oxides: an ab initio study10.1021/jp984420a ↗
3. Thermoelectric properties of CuAlO210.1016/j.jeurceramsoc.2005.03.034 ↗
4. Density functional theory study of 3R– and 2H–CuAlO2 in tensile stress10.1016/j.physleta.2011.02.062 ↗
5. P-type electrical conduction in transparent thin films of CuAlO210.1038/40087 ↗
6. Thermoelectric properties of single crystal CuAlO2 with a layered structure10.1039/b006850k ↗
7. Effect of partial substitution of Ca for Al on the microstructure and high-temperature thermoelectric properties of CuAlO210.1016/j.mseb.2005.10.035 ↗
8. Non-calcining process for CuAlO2 and CuAl0.9Ca0.1O2 ceramics10.1016/j.jallcom.2007.12.016 ↗
9. Improvement in thermoelectric properties of CuAlO2 by adding Fe2O310.1016/j.jallcom.2006.07.067 ↗
10. Effects of mechanical milling on preparation and properties of CuAl1−xFexO2 thermoelectric ceramics10.1016/j.ceramint.2011.12.079 ↗
11. Thermoelectric and optical properties of CuAlO2 synthesized by direct microwave heating10.1016/j.cap.2014.06.024 ↗
12. Optimum sintering temperature for thermoelectric properties of low-cost CuAl0.90Fe0.10O2 material10.1007/s10854-016-5227-5 ↗
13. Power factor improvement of delafossite CuAlO2 by liquid-phase sintering with Ag2O addition10.1016/j.mssp.2016.08.023 ↗
14. Porous ceramics with tri-modal pores prepared by foaming and starch consolidation10.1016/j.ceramint.2006.08.009 ↗
15. Effect of starch addition on microstructure and properties of highly porous alumina ceramics10.1016/j.ceramint.2013.04.072 ↗
16. Preparation and properties of oxidized starch with high degree of oxidation10.1016/j.carbpol.2011.11.036 ↗
17. Thermoelectric properties of hot-pressed and PECS-sintered magnesium-doped copper aluminum oxide10.1007/s11664-011-1508-1 ↗
18. Mn-substitution effect on thermal conductivity of delafossite-type oxide CuFeO210.1007/s11664-010-1135-2 ↗
19. Schwartz · 1963
20. Dependence of thermal conductivity on structural parameters in porous samples10.1063/1.3676435 ↗
21. A variational approach to the theory of the effective magnetic permeability of multiphase materials10.1063/1.1728579 ↗
22. Thermal conductivity bounds for isotropic, porous materials10.1016/j.ijheatmasstransfer.2004.12.032 ↗
23. Transport and defect mechanisms in cuprous delafossites. 1. Comparison of hydrothermal and standard solid-state synthesis in CuAlO210.1021/cm048983c ↗