journal article·2021-04

Magnetic and mechanical characterization of Al-MWCNT-Fe-Ni hybrid metal matrix composites

Alexandre Tugirumubano, Sun Ho Go, Hee Jae Shin, Vijay Santhiyagu Joseph, Lee Ku Kwac, Hong Gun Kim

Publisher page

Abstract

Abstract This paper aimed to synthesize the aluminum (Al) based magnetic hybrid composites by using iron nanoparticles (Fe: 16–28 vol%), nickel nanoparticles (Ni: 2 vol%) and multi-wall carbon nanotubes (MWCNT: 2 vol%) as reinforcements. The magnetic, mechanical, electrical properties were investigated. The highest saturation magnetization of 79.21 emu/g was given by the composite with high volume fraction of iron nanoparticles. However, with an addition of nickel (2 vol%) in Al-MWCNT-Fe, the magnetic properties were decreased. A reduction of power losses up to 41.5% was achieved by using Ni 2 vol%. It was also found that the composites with greater aluminum content had better tensile strength with the highest strength of 68.5 MPa and better flexural strength. The greatest hardness of HV 74 was achieved by increasing the Fe content. The electrical resistivity varied between 1354 µΩ.cm and 2450 µΩ.cm, which is higher than that of commercial aluminum and some of its alloys.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Aluminum Alloys Composites Properties · Electromagnetic wave absorption materials · Metallic Glasses and Amorphous Alloys

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (58)

Show source-provided references
1. Effect of carbon nanotube (CNT) content on the properties of in-situ synthesis CNT reinforced Al composites10.1016/j.msea.2016.02.062 ↗
2. Aluminium metal matrix composites - A review
3. Investigation of impact behaviour of aluminium based SiC particle reinforced metal-matrix composites10.1016/j.compositesa.2006.02.026 ↗
4. Processing of advanced Al/SiC particulate metal matrix composites under intensive shearing - A novel Rheo-process10.1016/j.compositesa.2008.10.017 ↗
5. Combined effects of reinforcement fraction and porosity on ultrasonic velocity in SiC particulate aluminum alloy matrix composites10.1016/j.compositesb.2017.01.017 ↗
6. Graphene encapsulated SiC nanoparticles as tribology-favoured nanofillers in aluminium composite10.1016/j.compositesb.2018.12.046 ↗
7. Synthesis and characterization of sintered hybrid aluminium matrix composites reinforced with nanocopper oxide particles and microsilicon carbide particles10.1016/j.compositesb.2013.10.060 ↗
8. B.R. Reddy, C. Srinivas, Fabrication and Characterization of Silicon Carbide and Fly Ash Reinforced Aluminium Metal Matrix Hybrid Composites, in: Mater. Today Proc., Elsevier Ltd, 2018: pp. 8374–8381. https://doi.org/10.1016/j.matpr.2017.11.531.10.1016/j.matpr.2017.11.531 ↗
9. Microstructure and wear characterization of aluminum matrix composites reinforced with industrial waste fly ash particulates synthesized by friction stir processing10.1016/j.matchar.2016.05.017 ↗
10. Graphene oxide-reinforced aluminium-matrix nanostructured composites fabricated by accumulative roll bonding10.1016/j.compositesb.2018.11.075 ↗
11. Carbon fiber reinforced metal matrix composites: Fabrication processes and properties10.1016/j.compositesa.2016.10.032 ↗
12. Laminate squeeze casting of carbon fiber reinforced aluminum matrix composites10.1016/j.matdes.2014.11.034 ↗
13. Processing, structure and thermal conductivity correlation in carbon fibre reinforced aluminium metal matrix composites10.1016/j.matdes.2018.06.059 ↗
14. Microstructure and tensile properties of 2014 Al alloy reinforced with continuous carbon fibers manufactured by gas pressure infiltration
15. A novel approach to prepare aluminium-alloy foams reinforced by carbon-nanotubes10.1016/j.matlet.2015.07.115 ↗
16. Recent progress in the development and properties of novel metal matrix nanocomposites reinforced with carbon nanotubes and graphene nanosheets10.1016/j.mser.2013.08.001 ↗
17. Dispersion of carbon nanotubes (CNTs) in aluminum powder10.1016/j.compositesa.2006.04.006 ↗
18. CNT reinforced aluminium matrix composite-a review10.1016/j.matpr.2015.07.248 ↗
19. Effect of ball-milling time on mechanical properties of carbon nanotubes reinforced aluminum matrix composites10.1016/j.compositesa.2012.07.026 ↗
20. Fatigue behavior of Al2024 alloy-matrix nanocomposites reinforced with multi-walled carbon nanotubes10.1016/j.compositesb.2017.09.034 ↗
21. S.E. Shin, Y.J. Ko, D.H. Bae, Mechanical and thermal properties of nanocarbon-reinforced aluminum matrix composites at elevated temperatures, (2016). https://doi.org/10.1016/j.compositesb.2016.09.017.10.1016/j.compositesb.2016.09.017 ↗
22. Structural and thermal characterization of multiwall carbon nanotubes (MWCNTs) / aluminum (Al) nanocomposites10.1016/j.compositesb.2018.06.019 ↗
23. Magnetic and electrical properties of aluminium matrix composite reinforced with magnetic nano iron oxide (Fe3O4)
24. The surface and bulk magnetic properties of Fe-Al alloys10.12693/APhysPolA.126.58 ↗
25. Effect of iron addition on microstructure, mechanical and magnetic properties of Al-matrix composite produced by powder metallurgy route10.1016/S1003-6326(15)63577-4 ↗
26. Numerical simulation and experimental validation of electromagnetic properties for Al-MWCNT-Fe2O3 hybrid nano-composites10.1016/j.jallcom.2017.10.010 ↗
27. Table of Electrical Resistivity and Conductivity, (n.d.). https://www.thoughtco.com/table-of-electrical-resistivity-conductivity-608499 (accessed September 24, 2020).
28. Microstructural and mechanical characterization of Al-MWCNT composites produced by mechanical milling10.1016/j.msea.2008.10.047 ↗
29. Combination of hot extrusion and spark plasma sintering for producing carbon nanotube reinforced aluminum matrix composites10.1016/j.carbon.2008.10.041 ↗
30. Mechanical properties and microstructures of carbon nanotube-reinforced Al matrix composite fabricated by in situ chemical vapor deposition10.1016/j.jallcom.2009.07.099 ↗
31. Preparation of nanocrystalline Fe-Ni powders by mechanical alloying used in soft magnetic composites10.1016/j.jmmm.2007.10.033 ↗
32. Experimental investigation of the effect of nickel on the electrical resistivity of Fe-Ni and Fe-Ni-S alloys under pressure10.2138/am-2020-7301 ↗
33. The influence of carbon nanotube (CNT) morphology and diameter on the processing and properties of CNT-reinforced aluminium composites10.1016/j.compositesa.2010.11.008 ↗
34. A theoretical evaluation of the effects of carbon nanotube entanglement and bundling on the structural and mechanical properties of buckypaper10.1016/j.carbon.2011.12.027 ↗
35. Magnetic, Electrical, and Mechanical Behavior of Fe-Al-MWCNT and Fe-Co-Al-MWCNT Magnetic Hybrid Nanocomposites Fabricated by Spark Plasma Sintering10.3390/nano10030436 ↗
36. The effect of the processing parameters on the properties of the liquid phase spark plasma sintered 80Fe-20(Al + MWCNT) magnetic metal matrix nanocomposites10.3390/met10070962 ↗
37. Synthesis of maghemite (γ-Fe2O3) nanoparticles by thermal-decomposition of magnetite (Fe3O4) nanoparticles10.2478/s13536-012-0100-6 ↗
38. Method for Determining Crystal Grain Size by X-Ray Diffraction10.1002/crat.201700157 ↗
39. Sunday · 2017
40. Prediction of the Elastic Modulus of Wood Flour/Kenaf Fibre/Polypropylene Hybrid Composites
41. Prediction of tensile properties of hybrid-natural fiber composites10.1016/j.compositesb.2011.08.023 ↗
42. Densification behaviour of mixtures of hard and soft powders under pressure10.1016/S0032-5910(99)00293-4 ↗
43. Density measurement of size selected multiwalled carbon nanotubes by mobility-mass characterization10.1016/j.carbon.2009.01.011 ↗
44. Spaldin · 2010
45. Generalized inclusion model for the coercivity of soft magnetic materials10.1063/1.367458 ↗
46. Amorphous and nanocrystalline materials for applications as soft magnets10.1016/S0079-6425(99)00002-X ↗
47. Structural, magnetic, and mechanical properties of electrodeposited cobalt-tungsten alloys: Intrinsic and extrinsic interdependencies10.1016/j.electacta.2013.04.022 ↗
48. R. Skomski, D.J. Sellmyer, Intrinsic and Extrinsic Properties of Advanced Magnetic Materials, in: Handb. Adv. Magn. Mater., 2008: pp. 1–57. https://doi.org/10.1007/1-4020-7984-2_1.10.1007/1-4020-7984-2_1 ↗
49. Interface magnetic anisotropy10.1016/0304-8853(95)01093-9 ↗
50. Pinning effect of the grain boundaries on magnetic domain wall in FeCo-based magnetic alloys10.1063/1.370175 ↗
51. Characterization and amorphous phase formation of mechanically alloyed Co60Fe5Ni5Ti25B5 powders10.1016/j.jallcom.2015.07.268 ↗
52. Mechanism of magnetic hysteresis in heterogeneous alloys
53. Cullity · 2009
54. Resistivity and core size dependencies of eddy current loss for Fe-Si compressed cores10.1109/TMAG.2005.854905 ↗
55. Core-loss analysis of an (Fe Co, Ni)-based nanocrystalline soft magnetic alloy10.1063/1.1847333 ↗
56. The Effect of Nickel on the Thermal Conductivity of Al-Si Cast Alloys, ICAA13 13th Int
57. Strengthening Aluminum Scrap by Alloying with Iron
58. J.W. Holladay, Review of Developments in Iron-Aluminum-Base Alloys, Battelle Memorial Institute, Defense Metals Information Center, Colombus, Ohio, 1961. https://babel.hathitrust.org/cgi/pt?id=mdp.39015095152248&view=1up&seq=8.