journal article·2021-05

Silicon carbonitride ceramic surface-modified nanoporous aluminum alloy by preceramic polysilazane precursor for surface strengthening

Lung-Hao Hu, Yu-Kai Wang

Publisher page

Abstract

Abstract Preceramic polysilazane precursor is simply coated on the anodized 7003 alloy and pyrolyzed at 400, 500 and 600 °C, respectively to form a silicon carbonitride ceramic film. The scanning and transmission electron microscopic images show that silicon carbonitride film can be detected on the surface of the anodic aluminum oxide compactly, representing a multilayer structure with the films of SiCN, SiCN with anodic aluminum oxide (AAO) layer and 7003 alloy substrate. The wear test is built-up by a stainless steel velvet head with reciprocating movement. After wearing in 2.176 km, the wear rate of the SiCN coated 7003 alloy pyrolyzed at 600 °C is about 0.003%, extremely lower than that of the anodized 7003 alloy, 0.023%. The average surface hardness and indentation modulus of elasticity can achieve higher than 6 GPa and 85–90 GPa that are twice higher than those of the anodized 7003 alloy.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Anodic Oxide Films and Nanostructures · Advanced ceramic materials synthesis · Corrosion Behavior and Inhibition

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (37)

Show source-provided references
1. Ceramic coatings for aluminum engine blocks10.4271/911719 ↗
2. Yamaha DiASil, .
3. Phase composition, microstructure and microhardness of electroless nickel composite coating co-deposited with SiC on cast aluminium LM24 alloy substrate10.1016/j.surfcoat.2013.08.063 ↗
4. Electrodeposition of Co-B/SiC composite coatings: characterization and evaluation of wear volume and hardness10.3390/coatings9040279 ↗
5. Comparative study of DC and RF sputtered MoSe2 coatings containing carbon—an approach to optimize stoichiometry
6. On the significance of the H/E ratio in wear control: a nanocomposite coating approach to optimised tribological behavior10.1016/S0043-1648(00)00488-9 ↗
7. Relationships between hardness, Young’s modulus and elastic recovery in hard nanocomposite coatings10.1016/S0257-8972(01)01714-5 ↗
8. Effects of normal load on nanotribological properties of sputtered carbon nitride films10.1016/j.diamond.2004.07.022 ↗
9. Tribological behaviors of Pb/MoS2 film under electrical condition in vacuum10.1088/2053-1591/ab144b ↗
10. Hot-injection for synthesizing ammonium thiosulfate precursor of molybdenum disulfide thin film coated on nano-porous aluminum oxide for surface strengthening
11. High-entropy ceramic thin films; A case study on transition metal diborides10.1016/j.scriptamat.2018.02.008 ↗
12. Fracture toughness and structural evolution in the TiAlN system upon annealing10.1038/s41598-017-16751-1 ↗
13. Polymer-derived ceramics: 40 years of research and innovation in advanced ceramics10.1111/j.1551-2916.2010.03876.x ↗
14. Fabrication of SiCN MEMS by photopolymerization of pre-ceramic polymer10.1016/S0924-4247(01)00723-3 ↗
15. Processing and characterization of silicon carbon-nitride ceramics: application of electrical properties towards MEMS thermal actuators10.1016/S0924-4247(02)00330-8 ↗
16. SiCN functionalized carbon nanotube gas sensors for elevated temperature applications10.1111/jace.13396 ↗
17. Gas Sensing Behavior of Mesoporous SiOC Glasses10.1111/jace.12491 ↗
18. Tribological characterisation of silicon carbonitride ceramics derived from preceramic polymers10.1016/j.wear.2005.04.031 ↗
19. Fabrication and characterisation of fully dense Si-C-N ceramics from a liquid poly(ureamethylvinyl) silazane precursor10.1016/j.jeurceramsoc.2008.05.028 ↗
20. Corrosion resistant polymer derived ceramic composite environmental barrier coatings10.1016/j.jeurceramsoc.2014.05.036 ↗
21. Amorphous silicoboron carbonitride ceramic with very high viscosity at temperatures above 1500 °C10.1111/j.1151-2916.1998.tb02780.x ↗
22. Oxidation kinetics of an amorphous silicon carbonitride ceramic10.1111/j.1151-2916.2001.tb00918.x ↗
23. PDC glass/ceramic coatings applied to differently pretreated AISI441 stainless steel substrates10.3390/ma13030629 ↗
24. Fabrication of high quality anodic aluminum oxide (AAO) on low purity aluminum—a comparative study with the AAO produced on high purity aluminum10.1016/j.electacta.2013.04.160 ↗
25. Effect of inter-electrode separation in the fabrication of nanoporous alumina by anodization10.1016/j.jelechem.2018.05.038 ↗
26. The impact of viscosity of the electrolyte on the formation of nanoporous anodic aluminum oxide10.1016/j.electacta.2014.04.039 ↗
27. Fabrication of self-ordered porous alumina via etidronic acid anodizing and structural color generation from submicrometer-scale dimple array10.1016/j.electacta.2014.12.171 ↗
28. Characterization of nanopores arrangement of anodic alumina layers synthesized on low-(AA1050) and high-purity aluminium by two-step anodizing in sulfuric acid with addition of ethylene glycol at low temperature10.1007/s10934-016-0316-7 ↗
29. The anodic treatment of aluminum in sulfuric acid solutions10.1149/1.2430017 ↗
30. N.A. Belov Page, Multicomponent Phase Diagrams: Applications for Commercial Aluminum Alloys, pp. 193-222. ISBN 978-0080445373.
31. Raj · J Am Ceram Soc. · 2019 · 102 · 92410.1111/jace.16089 ↗
32. Silicon-containing polymer-derived ceramic nanocomposites (PDC-NCs): preparative approaches and properties10.1039/c2cs15319j ↗
33. .
34. Polymer derived engineering ceramics10.1002/1527-2648(200006)2:6<339::AID-ADEM339>3.0.CO;2-K ↗
35. Borasilazane polymeric precursors for borosilicon nitride10.1111/j.1151-2916.1990.tb05286.x ↗
36. Synthesis, characterization, and ceramic conversion reactions of borazine-modified hydridopolysilazanes: new polymeric precursors to silicon nitride carbide boride (SiNCB) ceramic composites10.1021/cm00028a024 ↗
37. Nanoindentation and nanoscratching of hard carbon coatings for magnetic disks10.1557/PROC-383-447 ↗