Optimizing cathode contact layer thickness for enhanced efficiency and durability in solid oxide fuel cell stacks
Source abstract
Abstract
The introduction of a contact layer between the cathode and the interconnect effectively reduces their interfacial resistance and improves overall solid oxide fuel cell performance. In this study, LaCo0.4Ni0.6O3 (LCN) was selected as the cathode contact material due to its excellent electrical conductivity, excellent chemical compatibility, and thermal expansion coefficient (TEC) well matched with adjacent cell components. A series of thicknesses of the LCN layer was systematically investigated to elucidate its impact on cell performance. Experimental results demonstrated a peak power output of 104.28 W at 750 °C with an optimal LCN thickness of 0.4 mm, accompanied by robust long-term stability. A 22-cell stack achieved a total power output of 1144.8 W at 750 °C, maintaining stable operation with an average efficiency decay of only 0.5 % over five thermal cycles. Excessive thickness hindered reactant gas diffusion, while inadequate thickness caused localized cathode overheating (“burning”), leading to premature cell failure. These findings underscore the necessity of optimizing LCN contact layer thickness to achieve a balance between electrical performance, gas transport efficiency, and thermal management in SOFC stacks.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Fuel Cells and Related Materials · Catalysis and Oxidation Reactions
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (51)
Show source-provided references
1. Microstructure evolution in a solid oxide fuel cell stack quantified with interfacial free energy10.3390/en14123476 ↗
2. Entropy engineering design of high-performing lithiated oxide cathodes for proton-conducting solid oxide fuel cells10.26599/JAC.2023.9220804 ↗
3. Cathode infiltration with enhanced catalytic activity and durability for intermediate-temperature solid oxide fuel cells10.1016/j.cclet.2021.07.037 ↗
4. Robust Ruddlesden-popper phase Sr3Fe1.3Mo0.5Ni0.2O7-δ decorated with in-situ exsolved Ni nanoparticles as an efficient anode for hydrocarbon fueled solid oxide fuel cells10.1002/sus2.58 ↗
5. Effect of rib width on the thermo-electro-mechanical behavior of solid oxide fuel cells
6. Manipulating Nb-doped SrFeO3−δ with excellent performance for proton-conducting solid oxide fuel cells10.26599/JAC.2024.9220880 ↗
7. Cathode-side electrical contact and contact materials for solid oxide fuel cell stacking: a review10.1016/j.ijhydene.2017.08.005 ↗
8. Three-dimensional multi-physics modelling and structural optimization of SOFC large-scale stack and stack tower10.1016/j.ijhydene.2022.10.146 ↗
9. Thermoelectrical comprehensive analysis and optimization of multi-stack solid oxide fuel cell system10.1016/j.enconman.2023.117297 ↗
10. BaCe0.8Fe0.1Ni0.1O3−δ-impregnated Ni–GDC by phase-inversion as an anode of solid oxide fuel cells with on-cell dry methane reforming10.26599/JAC.2024.9220902 ↗
11. Effect of flow modes on operation characteristics of three-dimensional non-isothermal solid oxide fuel cell stack10.1002/er.7210 ↗
12. Performance study of solid oxide fuel cell with Ni-foam indirect internal reformer: intrinsic reforming kinetics and temperature uniformity10.1016/j.cej.2022.141170 ↗
13. Tailoring gadolinium-doped ceria-based solid oxide fuel cells to achieve 2 W cm−2 at 550 °C10.1038/ncomms5045 ↗
14. Solid oxide fuel cell stack with enhanced performance and durability utilizing a porous ag coating layer as the current collector10.1016/j.ijhydene.2024.05.284 ↗
15. An innovative and facile synthesis route of (La,Sr)2FeO4+δ–La0.4Sr0.6FeO3−δ composite as a highly stable air electrode for reversible solid oxide cell applications10.26599/JAC.2024.9220938 ↗
16. Tailoring cobalt-free La0.5Sr0.5FeO3-δ cathode with a nonmetal cation-doping strategy for high-performance proton-conducting solid oxide fuel cells10.1002/sus2.79 ↗
17. Tailoring SrFeO3 cathode with ta and F allows high performance for proton-conducting solid oxide fuel cells
18. Chromium deposition and poisoning of La2NiO4 cathode of solid oxide fuel cell10.1098/rsos.180634 ↗
19. Performance degradation and analysis of 10-cell anode-supported SOFC stack with external manifold structure10.1016/j.energy.2016.12.107 ↗
20. Comparison of iron and copper doped manganese cobalt spinel oxides as protective coatings for solid oxide fuel cell interconnects10.1016/j.jpowsour.2017.10.060 ↗
21. The structural properties and high-temperature oxidation behavior of co-Mn spinel coatings for SOFC interconnect application10.1007/s12666-024-03469-8 ↗
22. Degradation analysis and durability improvement for SOFC 1-cell stack10.1016/j.apenergy.2016.04.094 ↗
23. LaNi0.6Fe0.4O3 cathode contact material: electrical conducting property manipulation and its effect on SOFC electrochemical performance
24. Progress and challenges of cathode contact layer for solid oxide fuel cell10.1016/j.ijhydene.2020.09.147 ↗
25. Stability analysis of the Interface between electrical contact layers and metal interconnects in solid oxide fuel cells10.1149/1.2729168 ↗
26. Novel perovskite-spinel composite conductive ceramics for SOFC cathode contact layer10.1016/j.ijhydene.2018.10.159 ↗
27. Effect of electric current on cathode-side contact resistance in SOFC stacks10.1016/j.ijhydene.2024.12.405 ↗
28. Investigation of a spinel-forming cu-Mn foam as an oxygen electrode contact material in a solid oxide cell single repeating unit10.1002/fuce.201700005 ↗
29. A real proton-conductive, robust, and cobalt-free cathode for proton-conducting solid oxide fuel cells with exceptional performance10.1002/sus2.156 ↗
30. Interface design for enhancing the performance of solid oxide cell contact layers between interconnects and solid oxide cells10.1016/j.ssi.2025.116841 ↗
31. Investigation of high-entropy alloy derived spinel-based layer for SOFC cathode-side contact application10.1002/fuce.202300117 ↗
32. Advances in component and operation optimization of solid oxide electrolysis cell10.1016/j.cclet.2022.108035 ↗
33. Chemical compatibility and electrical contact of LaNi0.6Co0.4O3–δ (LNC) between Crofer22APU interconnect and La0.6Sr0.4FeO3 (LSF) cathode for IT-SOFC10.1002/fuce.201300016 ↗
34. Evaluation of using LaNi0.6Fe0.4O3–δ contact layer between La0.6Sr0.4FeO3 cathode and Crofer22APU interconnect for solid oxide fuel cells10.1002/fuce.201500208 ↗
35. Stack-like contacting in solid oxide cells: electrochemical characterization and Modeling10.1149/1945-7111/ad3a16 ↗
36. Highly-conductive and durable SOFC cathode-side contact based on reactively-sintered Mn-co spinel10.1149/1945-7111/ad11b0 ↗
37. Stability study on a novel micro structure configuration of cathode contact layer for solid oxide fuel cell stack10.1016/j.ijhydene.2016.03.059 ↗
38. A proton-conducting solid oxide fuel cell for co-production of ethylene and power via ethane conversion10.1016/j.cclet.2024.110171 ↗
39. An active and stable hydrogen electrode of solid oxide cells with exsolved Fe–co–Ni nanoparticles from Sr2FeCo0.2Ni0.2Mo0.6O6-δ double-perovskite10.1016/j.apmate.2023.100133 ↗
40. Visiting the roles of Sr- or ca- doping on the oxygen reduction reaction activity and stability of a perovskite cathode for proton conducting solid oxide fuel cells10.1002/sus2.101 ↗
41. Multiphase engineering regulation of double perovskite and RP structure heterojunction interfaces for solid oxide fuel cells
42. Performance of a novel La(Sr)MnO3-Pd composite current collector for solid oxide fuel cell cathode10.1016/j.jpowsour.2010.12.099 ↗
43. Mechanical and electrochemical performance of composite cathode contact materials for solid oxide fuel cells10.1016/j.jpowsour.2013.03.130 ↗
44. Deposition of La0.8Sr0.2Cr0.97V0.03O3 and MnCr2O4 thin films on ferritic alloy for solid oxide fuel cell application10.1016/j.surfcoat.2007.07.046 ↗
45. High toughness well conducting contact layers for solid oxide cell stacks by reactive oxidative bonding10.1016/j.jeurceramsoc.2020.11.021 ↗
46. Conductive spinels derived from co–Mn based alloy precursor for SOFC cathode-side contact application10.1016/j.ijhydene.2020.07.153 ↗
47. The investigation of ag & LaCo0.6Ni0.4O3−δ composites as cathode contact material for intermediate temperature solid oxide fuel cells10.1016/j.ijhydene.2018.03.150 ↗
48. Chemical compatibility and electrical contact between Ni–Cr–Mo alloy and LaCo0.6Ni0.4O3−δ in intermediate temperature solid oxide fuel cells10.1016/j.ijhydene.2012.08.135 ↗
49. Duan · 2013 · 57 · 891
50. Factors of cathode current-collecting layer affecting cell performance inside solid oxide fuel cell stacks10.1016/j.ijhydene.2014.08.116 ↗
51. Optimization of cathode structure for anode-supported planar solid oxide fuel cell