Advancing proton-conducting ceramic cells with thin electrolyte layers prepared by wet powder spraying
Source abstract
Abstract
• A 3 μm proton-conducting electrolyte was made via wet powder spraying. • Thin electrolyte enables proton transport without grain boundary obstruct. • Dense electrolyte layer achieved at 1375 °C on SrZr 0.5 Ce 0.4 Y 0.1 O 3 -based substrate. • 422 mW/cm 2 power density reached at 600 °C, 0.7 V in fuel cell mode. The development of proton conducting high temperature solid state electrochemical cells (PCCs) is vital for energy conversion and storage. Here, a SrZr 0.5 Ce 0.4 Y 0.1 O 3-δ (SZCY) / NiO supported cell with a 3 μm BaZr 0.16 Ce 0.64 Y 0.1 Yb 0.1 O 3-δ electrolyte, deposited by wet powder spraying (WPS), was fabricated. Co-sintering at 1375 °C yielded a dense electrolyte layer with large grains. Sr diffusion from the SZCY substrate compensated for Ba evaporation, preventing the formation of Y-rich secondary phases and thereby enhancing sinterability. STEM confirmed elemental diffusion and verified the proton transport without grain boundary obstruct in the thin electrolyte layer. The fabricated PCC achieved 422 mW cm −2 at 0.7 V and 600 °C in fuel cell mode, demonstrating competitive electrochemical performance. Minor defects in the electrolyte layer contributed to reduced open-circuit voltage (OCV) at lower temperatures, attributed to contamination during substrate pre-treatment. This work demonstrates the viability of WPS for scalable fabrication of thin PCC electrolyte layers with enhanced electrochemical performance.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advancements in Solid Oxide Fuel Cells · Fuel Cells and Related Materials · Gas Sensing Nanomaterials and Sensors
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (30)
Show source-provided references
1. Perspective of perovskite-type oxides for proton conducting solid oxide fuel cells10.1016/j.ssi.2019.04.014 ↗
2. From Electrolyte and Electrode Materials to Large‐Area Protonic Ceramic Fuel Cells: A Review
3. Advanced Materials for Thin-Film Solid Oxide Fuel Cells: Recent Progress and Challenges in Boosting the Device Performance at Low Temperatures
4. 5 × 5 cm2 protonic ceramic fuel cell with a power density of 1.3 W cm–2 at 600 °C10.1038/s41560-018-0230-0 ↗
5. Boosting intermediate temperature performance of solid oxide fuel cells via a tri‐layer ceria–zirconia–ceria electrolyte10.1111/jace.18482 ↗
6. Novel high-performance solid oxide fuel cells with bulk ionic conductance dominated thin-film electrolytes10.1016/j.jpowsour.2012.06.087 ↗
7. Lowering the operating temperature of protonic ceramic electrochemical cells to <450 °C
8. Enhanced grain boundary conductivity of Gd and Sc co-doping BaZrO3 proton conductor for proton ceramic fuel cell10.1016/j.cej.2023.143114 ↗
9. The relationship between chemical composition distributions and specific grain boundary conductivity in Y-doped BaZrO3 proton conductors10.1016/j.ssi.2008.12.006 ↗
10. High performance of protonic ceramic fuel cells with 1-μm-thick electrolytes fabricated by inkjet printing
11. Anode supported planar 5 × 5 cm2 SrZr0.5Ce0.4Y0.1O2.95 based solid oxide protonic fuel cells via sequential tape-casting10.1016/j.ssi.2022.115918 ↗
12. Large-area anode-supported protonic ceramic fuel cells combining with multilayer-tape casting and hot-pressing lamination technology10.1016/j.jeurceramsoc.2022.09.057 ↗
13. An efficient and durable anode for ammonia protonic ceramic fuel cells10.1039/D1EE02158C ↗
14. Scalable fabrication process for new structure BaZr0.8Y0.2O3-δ-based protonic ceramic fuel cells10.1016/j.ceramint.2021.01.264 ↗
15. Fabrication and characterization of Ba(Zr0.84Y0.15Cu0.01)O3 electrolyte-based protonic ceramic fuel cells10.1016/j.ceramint.2013.05.081 ↗
16. Highly dense and novel proton conducting materials for SOFC electrolyte10.1016/j.ijhydene.2017.09.067 ↗
17. Electrochemical analysis of high-performance protonic ceramic fuel cells based on a columnar-structured thin electrolyte10.1016/j.apenergy.2018.10.043 ↗
18. A review on sintering technology of proton conducting BaCeO3-BaZrO3 perovskite oxide materials for Protonic Ceramic Fuel Cells10.1016/j.jpowsour.2019.226991 ↗
19. Characterization of high Zr/Ce ratio Ba(Zr,Ce,Y)O3-δ proton conductors: investigating the impact of Y on the properties of materials10.1039/D4CP04384G ↗
20. Exceptionally high performance of protonic ceramic fuel cells with stoichiometric electrolytes10.1039/D1EE01497H ↗
21. Efficient intermediate-temperature steam electrolysis with Y : SrZrO3 –SrCeO3 and Y : BaZrO3 –BaCeO3 proton conducting perovskites10.1039/C8TA04019B ↗
22. Strontium doping effect on phase homogeneity and conductivity of Ba1−xSrxCe0.6Zr0.2Y0.2O3−δ proton-conducting oxides10.1016/j.ijhydene.2013.01.043 ↗
23. Effect of Strontium the phase structure of Ba1−xSrx Ce0.65Zr0.2Y0.15O3− δ (0 ≤ x ≤ 0.25) proton conductor by citrate–EDTA complexing sol–gel method10.1016/j.jascer.2016.12.004 ↗
24. Revitalizing interface in protonic ceramic cells by acid etch10.1038/s41586-022-04457-y ↗
25. Influence of Ba non-stoichiometry on the processing properties of Y- and Sc-doped BaZrO310.1016/j.jeurceramsoc.2024.04.070 ↗
26. Controlling Grain Boundary Segregation to Tune the Conductivity of Ceramic Proton Conductors
27. Influence of dopant levels on the hydration properties of SZCY and BZCY proton conducting ceramics for hydrogen production10.1016/j.ijhydene.2016.10.120 ↗
28. Electrochemical performance and chemical stability of proton‐conducting BaZr0.8-xCexY0.2O3−δ electrolytes
29. Ba 0.5Gd0.8La0.7Co2O6-δ Infiltrated in Porous BaZr0.7Ce0.2Y0.1O3 Backbones as Electrode Material for Proton Ceramic Electrolytes10.1149/2.0141704jes ↗
30. Gd- and Pr-based double perovskite cobaltites as oxygen electrodes for proton ceramic fuel cells and electrolyser cells10.1016/j.ssi.2015.05.014 ↗