journal article·2024-07

A novel method for air assisted nanosecond pulsed fiber laser beam transmission micro-channelling on thick PMMA material

S. Biswas, D. Pramanik, A. Sen, N. Roy, R. Biswas, A.S Kuar

Publisher page

Abstract

The demand for scaling up polymeric materials for mass production or scaling down for microscale applications is at its peak in the modern era. Laser beam technology enables the formation of micro-channels on polymers, specifically polymethyl methacrylate (PMMA). This study examines the viability and cost-effectiveness of employing the diode pump fiber laser transmission technique to create micro-channels on thick, transparent PMMA under air-assisted circumstances for biomedical engineering and micro-fluidics applications. The analysis has included process variables such as pulse frequency, power, and cutting speed, as well as machining parameters including depth of cut, kerf width, and heat-affected zone (HAZ) width. The results of multi-objective optimization indicate that the following parameters—a pulse frequency of 51.30 kHz, a working power of 13 % of 50 W, and a cutting speed of 0.60 mm/s—contribute to the desired microfluidics response values: 12.54 µm depth of cut, 24.05 µm kerf width, and 5.98 µm HAZ width.
Source: expertdata · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Laser Material Processing Techniques · Photonic Crystal and Fiber Optics · Advanced Fiber Laser Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (38)

Show source-provided references
1. Assessment of PMMA and polystyrene based microfluidic chips fabricated using CO2 laser machining10.1016/j.apsusc.2020.147642 ↗
2. CO2 Laser micromachining of polymethyl methacrylate (PMMA): a review10.1007/978-981-15-8542-5_82 ↗
3. Layered laser vaporization of PMMA manufacturing 3D mould cavities10.1016/j.cirp.2007.05.050 ↗
4. Prediction of laser cutting parameters for polymethylmethacrylate sheets using random vector functional link network integrated with equilibrium optimizer10.1007/s10845-020-01617-7 ↗
5. Predicting characteristics of dissimilar laser welded polymeric joints using a multi-layer perceptrons model coupled with archimedes optimizer10.3390/polym15010233 ↗
6. Imran, H.J., Hubeatir, K.A. and Al-Khafaji, M.M., 2021, March. CO2 laser micro-engraving of PMMA complemented by Taguchi and ANOVA methods. In Journal of Physics: Conference Series (Vol. 1795, No. 1, p. 012062). IOP Publishing.10.1088/1742-6596/1795/1/012062 ↗
7. Theoretical and experimental investigations of the influence of overlap between the laser beam tracks on channel profile and morphology in pulsed laser machining of polymers10.1016/j.ijleo.2018.06.066 ↗
8. Investigation and TGRA based optimization of laser beam drilling process during machining of Nickel Inconel 718 alloy10.1016/j.jmrt.2022.02.112 ↗
9. Tribological performance of gradient Ag-multilayer graphene/TC4 alloy self-lubricating composites prepared by laser additive manufacturing10.1080/10402004.2021.1922789 ↗
10. Surface quality measures analysis and optimization on machining titanium alloy using CO2 based laser beam drilling process10.1016/j.jmapro.2020.12.008 ↗
11. Modeling of the transient temperature field during laser heating10.1007/s40516-021-00138-2 ↗
12. Experimental approach to the laser machining of PMMA substrates for the fabrication of microfluidic devices10.1016/j.optlaseng.2010.11.013 ↗
13. Nanosecond pulsed laser micromachining of PMMA-based microfluidic channels10.1016/j.jmapro.2012.09.001 ↗
14. Pulsed laser micro-machining of polymer for micro-channel fabrication: Theory and experiment10.1016/j.infrared.2019.103068 ↗
15. Experimental investigation on laser cutting of PMMA sheets: Effects of process factors on kerf characteristics10.1016/j.jmrt.2021.01.012 ↗
16. May. Prediction of width and depth of cut in laser machining of PMMA using a CO2 laser
17. The effects of low-frequency workpiece vibration on low-power CO2 laser cutting of PMMA: an experimental investigation10.1007/s00170-011-3881-6 ↗
18. Evaluation of cutting quality of PMMA using CO2 lasers10.1007/s00170-006-0766-1 ↗
19. Laser cutting of polymeric materials: an experimental investigation10.1016/j.optlastec.2009.09.006 ↗
20. A study on the surface qualities of four polymer substrate microchannels using CO2 Laser for microfluidic chip10.1142/S0218625X18501603 ↗
21. Kant · 2015 · 221
22. Surface roughness analysis and improvement of PMMA-based microfluidic chip chambers by CO2 laser cutting10.1016/j.apsusc.2009.09.092 ↗
23. Kerf profile analysis and neural network-based modeling of increasing thickness PMMA sheets cut by CO2 laser10.1016/j.optlastec.2021.107386 ↗
24. Khoshaim, A.B., Elsheikh, A.H., Moustafa, E.B., Basha, M. and Showaib, E.A., 2021. Experimental investigation on laser cutting of PMMA sheets: Effects of process factors on kerf characteristics. journal of materials research and technology, 11, pp.235-246.10.1016/j.jmrt.2021.01.012 ↗
25. Experimental analysis of laser micromachining of microchannels in common microfluidic substrates10.3390/mi12020138 ↗
26. Dahotre · 2008
27. Issa · 2007
28. A fuzzy logic-based prediction model for kerf width in laser beam machining10.1080/10426914.2015.1037901 ↗
29. Experimental investigations and modeling for multi-pass laser micro-milling by soft computing-physics informed machine learning on PMMA sheet using CO2 laser10.1016/j.optlastec.2022.108922 ↗
30. Comparison of ANN and DoE for the prediction of laser-machined micro-channel dimensions10.1016/j.optlaseng.2009.04.009 ↗
31. Predicting kerf quality characteristics in laser cutting of basalt fibers reinforced polymer composites using neural network and chimp optimization10.1016/j.aej.2022.04.032 ↗
32. Improving laser cutting quality of polymethylmethacrylate sheet: experimental investigation and optimization10.1016/j.jmrt.2019.11.059 ↗
33. Kerf characteristics during CO2 laser cutting of polymeric materials: experimental investigation and machine learning-based prediction10.1016/j.jestch.2023.101519 ↗
34. Minimization of fume emissions in laser cutting of polyvinyl chloride sheets using genetic algorithm
35. Fabrication of trapezoidal cross-sectional microchannels on PMMA with a multi-pass translational method by CO2 laser10.1016/j.ijleo.2019.02.147 ↗
36. Experimental and parametric evaluation of cut quality characteristics in CO2 laser cutting of polystyrene10.1016/j.ijleo.2019.03.040 ↗
37. Cochran W.G., Cox G.M. Experimental Designs, second edition, Asia Publishing House India. (1977).
38. Montogomery · 2008