Preparation, thermoelectric properties and interface analysis of n-type graded material FeSi2/Bi2Te3
Source abstract
Abstract
Abstract Graded n-type β-FeSi 2 /Bi 2 Te 3 thermoelectric materials have been prepared by dip coating procedure using Sn 95 Ag 5 as bridge material. It was found that an apparent Seebeck coefficient is in between those of β-FeSi 2 and Bi 2 Te 3 below 150 °C and higher than both of them between 150 and 300 °C. A measurement shown that the maximum power output of the functionally graded material (FGM) is approximately 2.5–3 times that of monolithic material β-FeSi 2 at the same temperature difference, which suggests that not only do the graded material benefit the superior performance of Bi 2 Te 3 from low temperature side, but also make fully use of the properties of β-FeSi 2 at high one. Besides, the FGM revealed rather optimistic thermal stability with almost no power output loss even after annealing at 192 °C for 200 h, if a nickel layer was sandwiched between Sn 95 Ag 5 and Bi 2 Te 3 layers. An obvious diffusion of nickel element towards both Sn 95 Ag 5 and Bi 2 Te 3 sides was observed by EMPA, with the former being most likely occurred during long time annealing, and latter being irrelevant to annealing procedure applied.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Advanced Thermoelectric Materials and Devices · Thermal properties of materials · Thermodynamic and Structural Properties of Metals and Alloys
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (14)
Show source-provided references
1. Recent and prospective development of functionally graded materials in Japan10.4028/www.scientific.net/MSF.308-311.509 ↗
2. I. Shiota, I.A. Nishida, Development of FGM thermoelectric materials in Japan- the state of the art-, 1997 IEEE, 16th International Conference on Thermoelectrics (1997) 364–370.10.1109/ICT.1997.667154 ↗
3. Graded and stacked thermoelectric generators—numerical description and maximization of output power10.1016/S0921-5107(98)00211-6 ↗
4. Electric properties of Ni/n-PbTe and Ni/p-Pb0.5Sn0.5Te joined by plasma activated sintering10.4028/www.scientific.net/MSF.308-311.675 ↗
5. Thermoelectric generators made of FeSi2 and HMS: fabrication and measurement10.1557/JMR.1995.0034 ↗
6. Computational design for functionally graded thermoelectric materials10.4028/www.scientific.net/MSF.308-311.641 ↗
7. J. Schilz, L. Helmers, Y.S. Kang, Y. Noda, M. Niino, Bismuth-telluride/iron -disilicide segmented thermoelectric elements: patterning, preparation and properties, 1997 IEEE, 16th International Conference on thermoelectrics (1997) 375-378.
8. Electroless nickel plating to Bi–Te sintered alloy and its properties10.1007/BF00720166 ↗
9. R.J. Buist, S.J. Roman, Development of a burst voltage measurement system for high-resolution contact resistance tests of thermoelectric heterojunction, 2000 IEEE, 18th International Conference on Thermoelectrics, (1999) pp. 249–251.
10. The Preparation and performance of n-type FeSi2/Bi2Te3 segmented thermoelectric material
11. Expansion of utilizing temperature range of Bi2Te3/PbTe by FGM forming10.4028/www.scientific.net/MSF.308-311.693 ↗
12. M. Koshigoe, Y. Kudo, M. Hashimoto, I. Shiota, I.A. Nishida, Thermoelectric properties of segmented Bi2Te3/PbTe, 1998 IEEE, 17th International Conference on Thermoelectrics(1998) pp. 479–482.
13. Wiedemann–Franz law at boundaries10.1063/1.123420 ↗
14. J.L. Cui, X.B. Zhao, B.C. Zhou, X.B. Xu, M.D. Bao, Preparation and Interface Analyses of a P-Type Segmented FeSi2/Bi2Te3 Material, IEEE, 20th International Conference on Thermoelectrics (2001) 293–297.