Diamond composites of high thermal conductivity and low dielectric loss tangent
Source abstract
Abstract
Abstract Diamond-CaMg(CO3)2 and diamond-CaCO3 compacts were produced. Maximum values of high thermal conductivity of 540 W/m K, electrical resistivity of 2∙1011 ohm cm, dielectric constant of 47, and dielectric loss tangent of 5.8∙10-3 at 106 Hz were achieved. The composites based on diamonds were sintered at a high pressure of 8.0 GPa and temperature of 2100 °C and were characterised by high ratios of direct bonding between the diamond grains. Diamond grain size varied from 12 to 45 µm. The CaCO3 content of the diamond-CaCO3 composites and the CaMg(CO3)2 content of the diamond-CaMg(CO3)2 composites were 8.5 vol% and 8.8 vol%, respectively. The materials developed are recommended for use as heat sinks in a wide range of electronic devices.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Diamond and Carbon-based Materials Research · Advanced ceramic materials synthesis · Advanced materials and composites
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (18)
Show source-provided references
1. High thermal conductive AlN substrate for heat dissipation in high-power LEDs10.1016/j.ceramint.2018.09.171 ↗
2. Research on two-phase heat removal devices for power electronics10.1016/j.tsep.2018.09.012 ↗
3. A diamond made microchannel heat sink for high-density heat flux dissipation10.1016/j.applthermaleng.2019.113804 ↗
4. Fundamental limits for near-junction conduction cooling of high power GaN-on-diamond devices10.1016/j.ssc.2019.03.013 ↗
5. Single crystal diamond wafers for high power electronics10.1016/j.diamond.2016.03.013 ↗
6. A promising solution using CVD for efficient cooling of power devices10.1016/j.mseb.2012.03.005 ↗
7. High electrical resistivity of CVD-diamond10.1016/S0026-2714(98)00225-X ↗
8. Thermal conductivity of CVD diamond fibres and diamond fibre-reinforced epoxy composites10.1016/j.diamond.2004.10.039 ↗
9. Thermal conductivity of diamond composites sintered under high pressures10.1016/j.diamond.2007.12.051 ↗
10. Diamond formation and wettability in Mg-Cu-C system under high pressure and high temperature
11. Mechanical properties of a diamond-copper composite with high thermal conductivity10.1016/j.matdes.2015.08.048 ↗
12. Microstructure and thermal properties of copper-diamond composites with tungsten carbide coating on diamond particles10.1016/j.matchar.2014.07.025 ↗
13. J. Li, H. Zhang, Y. Zhang et al, Microstructure and thermal conductivity of Cu/diamond composites with Ti-coated diamond particles produced by gas pressure infiltration, Alloys Compd. 647 (2015) 941–946, doi: 10.1016/j.jallcom.2015.06.062.10.1016/j.jallcom.2015.06.062 ↗
14. Diamond-CaCO3 and diamond-Li2CO3 materials sintered using the HPHT method10.1016/j.jeurceramsoc.2017.02.028 ↗
15. Thermally stable polycrystalline diamond sintered with calcium carbonate10.1016/j.diamond.2007.08.011 ↗
16. Phase relation of CaCO3 at high pressure and high temperature10.2138/am-2001-8-906 ↗
17. Synthesis and characterisation of Ф62 mm polycrystalline diamond compact10.1016/j.diamond.2019.107594 ↗
18. A novel silica aerogel/porous Si3N4 composite prepared by freeze casting and sol-gel impregnation with high-performance thermal insulation and wave-transparent10.1016/j.matlet.2014.10.012 ↗