journal article·2022-02

Effects of ambient high-temperature annealing on microstructure, elemental composition, optical and electrical properties of indium tin oxide films

Kewei Sun, Chunli Yang, Dong Zhang, Dan Jin, Ying Wei, Hudie Yuan

Publisher page

Abstract

Abstract 500 nm-thickness indium tin oxide (ITO) films were deposited onto quartz glass substrates and annealed at 700–1000 °C for 1 h. Microstructure, elemental composition, optical and electrical properties of ITO films were systematically studied. It is found that the crystalline is cubic bixbyite, and preferred orientation changes from mainly (2 2 2) to (4 0 0) with the increasing temperature. Obvious changes are also observed in morphology of ITO films during the ambient high-temperature annealing. ITO film annealed up to 1000 °C is still stable Sn doped In2O3, oxygen defects decreases and adsorbed oxygen increases. The resistivity of ITO films after annealed at 700 and 800 °C firstly increases slightly and then increases sharply, when annealing temperature is increased to 900 and 1000 °C. Average transmittance of these films was 70%–80% and their optical band gap shifts to lower energy with the increase of the annealing temperature.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: ZnO doping and properties · Gas Sensing Nanomaterials and Sensors · Thin-Film Transistor Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (30)

Show source-provided references
1. Transparent thin films of indium tin oxide: morphology–optical investigations, inter dependence analyzes10.1016/j.apsusc.2017.02.106 ↗
2. Using Ag disc array to tune infrared transmittance of ITO-based multilayer films10.1016/j.jallcom.2019.01.273 ↗
3. Effects of second-phase particles and elemental distributions of ITO targets on the properties of deposited ITO films10.1016/j.ceramint.2017.04.021 ↗
4. Effect of ITO target crystallinity on the properties of sputtering deposited ITO films10.1016/j.ceramint.2019.11.110 ↗
5. Microstructure evolution of room-temperature-sputtered ITO films suitable for silicon heterojunction solar cells10.1016/j.cap.2020.06.007 ↗
6. Multilayer indium saving ITO thin films produced by sputtering method10.1016/j.jallcom.2020.154378 ↗
7. Indium tin oxide sputtering damage to catalytic chemical vapor deposited amorphous silicon passivation films and its recovery10.1016/j.tsf.2017.01.021 ↗
8. Correlation between the structure, specific resistance, and optical properties of ITO films grown by CVD10.3103/S0003701X1704003X ↗
9. Sol-gel derived ITO-based bi-layer and tri-layer thin film coatings for organic solar cells applications10.1016/j.apsusc.2020.147164 ↗
10. Optical, microstructural and vibrational properties of sol-gel ITO films10.1016/j.optmat.2021.110999 ↗
11. ITO film prepared by ion beam sputtering and its application in high-temperature thermocouple10.1016/j.vacuum.2017.08.046 ↗
12. Influence of thickness on crystallographic, stereometric, optoelectronic, and electrochemical characteristics of electron-beam deposited indium tin oxide thin films10.1016/j.matchemphys.2020.124051 ↗
13. Improvement of optical and electrical properties of ITO thin films by electro-annealing10.1016/j.vacuum.2015.06.027 ↗
14. Rapid thermal annealing effect of transparent ITO source and drain electrode for transparent thin film transistors10.1016/j.ceramint.2020.09.152 ↗
15. The main role of thermal annealing in controlling the structural and optical properties of ITO thin film layer10.1016/j.optmat.2021.110866 ↗
16. Improving Seebeck coefficient of ITO/AZO transparent film thermocouple by ITO (100) preferred orientation10.1016/j.sna.2020.112089 ↗
17. Annealing effects in ITO based ceramic thin film thermocouples10.1016/j.jallcom.2016.12.234 ↗
18. Fabrication and characterization of ITO thin film resistance temperature detector10.1016/j.vacuum.2016.07.028 ↗
19. Strain and temperature effects in indium-tin-oxide sensors10.1016/j.tsf.2010.04.116 ↗
20. Application of indium tin oxide (ITO) thin film as a low emissivity film on Ni-based alloy at high temperature10.1016/j.infrared.2016.07.021 ↗
21. Electrical and surface properties of indium tin oxide (ITO) films by pulsed DC magnetron sputtering for organic light emitting diode as anode material10.1016/j.surfcoat.2010.06.060 ↗
22. Effect of sputtering pressure and annealing temperature on the properties of indium tin oxide thin films10.1016/j.mseb.2006.08.058 ↗
23. Effect of cerium doping on the microstructure and photoelectric properties of Ce-doped ITO films10.1016/j.apsusc.2019.144810 ↗
24. Tuning defects in oxides at room temperature by lithium reduction10.1038/s41467-018-03765-0 ↗
25. Characterization broadband omnidirectional antireflection ITO nanorod films coating10.1016/j.optmat.2021.111545 ↗
26. Ultra-flat ITO films on mica for high temperature transparent flexible electrodes10.1016/j.ceramint.2019.09.215 ↗
27. Structural, optical and electrical characterization of ITO films co-doped with Molybdenum10.1016/j.solmat.2020.110904 ↗
28. Substrate temperature dependence of the properties of ZAO thin films deposited by magnetron sputtering10.1016/S0169-4332(03)00523-3 ↗
29. Effect of various annealing environments on electrical and optical properties of indium tin oxide on polyethylene napthalate10.1063/1.2204815 ↗
30. Thermal degradation behavior of indium tin oxide thin films deposited by radio frequency magnetron sputtering10.1557/JMR.2005.0199 ↗