journal article·2001-06

Specimen size effect on mechanical properties of polysilicon microcantilever beams measured by deflection using a nanoindenter

J.N. Ding, Y.G. Meng, S.Z. Wen

Materials Science and Engineering: B· Volume 83· Issue 1-3
Publisher page

Abstract

Abstract The validity of a novel, direct and convenient method for micromechanical property measurements by beam bending using a nanoindenter has been demonstrated. In the deflection of microbeams, the influence of the indenter tip pushing into the top of the microbeams and the curvature across its width must be considered. The elastic deflection of a polysilicon microcantilever beam will vary linearly with the force. Thus, Young's modulus of the beam determined from the slope of this linear relation is 156 Gpa±2.9–6.3%. The size effects of the manufactured component on Young's modulus and strength of polysilicon microcantilever beams were measured. This result shows that the rupture strengths of polysilicon beams show size effect on the effective volume and surface area of the specimens. The rupture strength of each sample decreased with increasing the specimen effective volume and surface area, but increased with increasing the surface-to-volume ratio. The defect that initiates fracture is often on the surface of the specimen. In such cases the size effect can be traced back to a surface-to-volume ratio as the governing parameter.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Force Microscopy Techniques and Applications · Mechanical and Optical Resonators · Advanced MEMS and NEMS Technologies

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. Future chips–micromachines—fomenting a revolution, in miniature10.1126/science.282.5388.402 ↗
2. Study on the fundamental design issues of microelectromechanical systems (MEMS)10.3901/JME.2000.07.039 ↗
3. J.A. Schweitz, Mechanical characterization of thin films by micromechanical techniques, MRS Bull. (1992) 34–45.10.1557/S0883769400041646 ↗
4. A new bulge test technique for the determination of Young's modulus and Poisson's ratio of thin films10.1557/JMR.1992.3242 ↗
5. A laser–acoustic method for testing and classifying hard surface layers10.1016/S0040-6090(98)00988-2 ↗
6. Measurement of micromechanical properties of polysilicon microstructures with an atomic force microscope10.1016/S0924-4247(98)00031-4 ↗
7. M-TEST: a test chip for MEMS material property measurement using electrostatically actuated test structures10.1109/84.585788 ↗
8. Magnetic-coil force actuator for microtensile test device
9. Elastic moduli, strength, and fracture initiation at sharp notches in etched single crystal silicon microstructures10.1063/1.369711 ↗
10. Relating mechanical testing and microstructural features of polysilicon thin films10.1557/JMR.1999.0094 ↗
11. Size effects in materials due to microstructural and dimensional constraints: A comparative review10.1016/S1359-6454(98)00231-6 ↗
12. Mechanical properties and fracture toughness of multilayer hard coatings using nanoindentation10.1016/S0040-6090(00)01004-X ↗
13. The effect of coating cracking on the indentation response of thin hard-coated systems10.1016/S0257-8972(97)00683-X ↗
14. Mechanical deflection of polysilicon microcantilever beams using nanoindentation10.3901/CJME.2000.04.251 ↗
15. Reliability considerations for electrostatic polysilicon actuators using as an example the REMO component10.1016/S0924-4247(97)80304-4 ↗
16. The fracture toughness of polysilicon microdevices: A first report10.1557/JMR.1997.0131 ↗
17. The properties of initial microbiology of polysilicon films
18. Specimen size effect on tensile strength of surface-micromachined polycrystalline silicon thin films10.1109/84.661392 ↗