Multiscale characterisation of the mechanical properties of austenitic stainless steel joints
Source abstract
Abstract
A multiscale investigation was pursued in order to obtain the strain distribution and evolution during tensile testing both at the macro- and micro-scale for a diffusion bonded 316L stainless steel. The samples were designed for the purpose to demonstrate that the bond line properties were equal or better than the parent material in a sample geometry that was extracted from a larger component. The macroscopic stress-strain curves were coupled to the strain distributions using a camera-based 2D – Digital Image Correlation system. Results showed significant amount of plastic deformation predominantly concentrated in shear bands which were extended over a large region, crossing through the joint area. Yet it was not possible to be certain whether the joint has shown significant plastic deformation. In order to obtain the joints’ mechanical response in more detail, in situ micromechanical testing was conducted in the SEM chamber that allowed areas of 1x1 mm2 and 50x50 mm2 to be investigated. The size of the welded region was rather small to be accurately captured from the camera based DIC system. Therefore a microscale investigation was pursued where the samples were tested within an SEM chamber. Low magnification SEM imaging was utilised in order to cover a viewing area of 1 mm×1 mm while high magnification SEM imaging was employed to provide evidence of the occurrence of plastic deformation within the joint, at an area of just 50 μm×50 μm. The strain evolution over the microstructural level, within the joint and at the base material was obtained. The local strains were highly non-homogeneous through the whole test. Final failure occurred approximately 0.2 mm away from the joint. Large local strains were measured within the joint region, while SEM imaging showed that plastic deformation occurs via the formation of strong slip bands, followed by the activation of additional slip systems upon further plastic deformation which end up in additional slip bands to form on the surface. Plastic deformation occurred by slip and twinning mechanisms. Upon necking, significant out of plane deformations and slip deformation mechanisms were observed which suggested that plastic deformation was also happening at the last stages of damage evolution for the specific alloy. This was also evident from the large difference between the 600 MPa UTS stress value and the low stress values before final failure (which in many cases was below 30 MPa).
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal Forming Simulation Techniques · Microstructure and Mechanical Properties of Steels · Microstructure and mechanical properties
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (20)
Show source-provided references
1. G. den Ouden, Lastechnologie,Delftse Uitgevers. Maatschappij, Derde druk 1993, pp. 120-134.
2. Welding Handbook, 8th Ed., Vol. 2, Welding processes, American Welding Society, Miami, 1991, chapter 1.
3. Welding Handbook, 8th Ed., Vol. 2, Welding processes, American Welding Society, Miami, 1991, chapter 1.
4. Correlation for shape, motion and deformation measurements: basic concepts
5. P. Efthymiadis, Multiscale Experimentation and Modeling of fatigue crack development in aluminium Alloy 2024 (PhD thesis), The University of Sheffield, pp 150–242, 2015.
6. Void nucleation and growth in dual-phase steel 600 during uniaxial tensile testing10.1007/s11661-009-0030-z ↗
7. A micro mechanical study on failure initiation of dual phase steels under tension using single crystal plasticity model10.1016/j.ijplas.2010.12.001 ↗
8. Digital image correlation studies for microscopic strain distribution and damage in dual phase steels10.1016/j.scriptamat.2007.01.031 ↗
9. Initiation and growth of damage in a dual-phase steel observed by X-ray microtomography10.1016/j.actamat.2008.06.015 ↗
10. Local plastic strain evolution in a high strength dual-phase steel10.1016/j.msea.2010.04.052 ↗
11. Microstructural banding effects clarified through micrographic digital image correlation10.1016/j.scriptamat.2010.02.014 ↗
12. Effect of martensite distribution on damage behaviour in DP600 dual phase steels10.1016/j.msea.2009.03.055 ↗
13. S.A. Soberanis, 3D CAFE Modelling of Ductile Fracture in Gas Pipeline Steel (PhD thesis), The University of Sheffield, pp. 42–45 & 69–82, 2007.
14. Continuum theory of ductile rupture by void nucleation and growth. Part I. Yield criteria and flow rules for porous ductile media10.1115/1.3443401 ↗
15. Ductile fracture models and their potential in local approach of fracture10.1016/0029-5493(87)90234-2 ↗
16. Void growth in an elastic-plastic medium10.1115/1.3422899 ↗
17. Influence of voids on shear band instabilities under plane strain conditions10.1007/BF00036191 ↗
18. Ductile fracture by cavity nucleation between larger voids10.1016/0022-5096(82)90033-3 ↗
19. On localization in ductile materials containing spherical voids10.1007/BF00015686 ↗
20. Analysis of the cup-cone fracture in a round tensile bar10.1016/0001-6160(84)90213-X ↗